Current Classifieds

Looking for fan shroud for 72' Pinto 1.6
Date: 04/13/2017 04:56 am
rear hatch back louvers

Date: 04/18/2017 12:44 pm
WANTED: 1979 Bumper End Caps - Front and Rear
Date: 02/16/2019 10:46 am
1973 Pinto Runabout

Date: 03/25/2019 09:02 pm
79 pinto headlight,tailight,side marker light assemblies

Date: 07/17/2018 09:22 pm
Mint Original Black Rear Seat $275.00

Date: 07/30/2020 11:45 am
1974 Pinto Passenger side door glass and door parts

Date: 02/28/2018 09:18 am
74 Driver side Wagon Fender, 74 driver side Door, Nice Wheels

Date: 09/15/2019 08:30 pm
KYB shocks

Date: 02/08/2017 07:09 pm
1978 Pinto Wagon V8
Date: 04/28/2023 03:26 pm
Looking for leaf spring insulators
Date: 04/04/2020 09:38 am
73 Caliper Retaining Key
Date: 10/28/2021 07:49 am

« previous next »
Pages: [1]   Go Down

Author Topic: 2.3L issue with idling  (Read 1518 times)

0 Members and 1 Guest are viewing this topic.

Offline MitchiePinto

  • Pinto Member
  • **
  • Posts: 76
  • FeedBack: +0/-0
  • Another Pinto Driver

    • Total Badges: 1
    Badges: (View All)
    Topic Starter
2.3L issue with idling
« on: September 05, 2012, 01:32:45 PM »
When I bought the car it was hard to start and had a leaking carb and idle was lumpy but it wouldn't quit and would run ok at about 500-650 rpm idle

Now I rebuilt the carb it starts easy but I have to keep my foot on the gas until it warms up (takes 6 mins) it idles at 2000 rpm when cold then around 1500 rpm when hot

The carb mixture is set lean (If I ran it richer it would bog out) Idle speed is set around 1500 rpm if I set it any lower the car would stall improperly

I suspect a vacuum leak (Il check with propane)

My carb is a 2100 Motorcraft without a choke mech.

Also I have a racing cam put into the head everything else in the engine bay is stock
Logged

Offline MitchiePinto

  • Pinto Member
  • **
  • Posts: 76
  • FeedBack: +0/-0
  • Another Pinto Driver

    • Total Badges: 1
    Badges: (View All)
    Topic Starter
Re: 2.3L issue with idling
« Reply #1 on: September 08, 2012, 03:26:46 PM »
UPDATE: Got the car running !!!!

The issue was the wrong power valve

In the kit it came with a 2 stage (I think) #28 power valve which made the car run rich and only stay running around 2000 rpm

I poped in my old power valve 1 stage #16 and fought with the float level until i got the smoothest idle

Now it idles around 500-750rpm (carb mixture screw's are set at 1 1/2 turns out )

No vacuum leaks, Car can handle slopes,loads and has no bogging or hesitating and the dieseling issue stopped

I have only the vacuum advance, PCV (from the air filter to the thing on top of the valve cover way in the back)

NOW one last issue the car has a mild lumpy idle like it wants to stall and if you listen closely you can hear a slight missfiring on idle and it vibrates some.

My hypothesis is that all this is being caused by the racing cam in it and I should check the ignition timing and advance the cam timing a little

Other than that the car is great it would do 100km all day long and Cruise fine its just the idle issue and I think it has an  overheating issue but im not sure. What are signs of overheating
Logged
Pages: [1]   Go Up
« previous next »