Current Classifieds

Want seals for Pinto wagon "flip out" windows
Date: 08/08/2017 01:44 pm
Pinto in Maine for sail...solid body

Date: 03/07/2017 07:03 pm
1979 PINTO PARTS--FREE
Date: 09/13/2022 02:05 pm
1978 need kick panels and rear hatch struts and upper and lower mounts
Date: 11/29/2018 10:26 am
1977 Pinto Cruizin Wagon

Date: 04/11/2024 03:56 pm
76 drivers fender
Date: 07/20/2018 08:24 pm
Radiator
Date: 05/27/2018 06:07 am
I have a 1977 Cobra body lots of parts here
Date: 04/12/2017 06:57 pm
Wanted Type 9 5spd Transmission
Date: 07/04/2017 03:26 pm
71-73 Front Kick Panels
Date: 04/25/2021 07:24 pm
front end parts
Date: 03/30/2018 12:48 pm
1980 Pinto-Shay for sale

Date: 07/07/2016 01:21 pm

« previous next »
Pages: [1]   Go Down

Author Topic: rear end swap  (Read 1723 times)

0 Members and 1 Guest are viewing this topic.

Offline junker

  • Pinto Member
  • **
  • Posts: 17
  • FeedBack: +1/-0
  • Another Pinto Driver

    • Total Badges: 2
    Badges: (View All)
    Topic Starter Windows User
rear end swap
« on: December 23, 2013, 01:54:59 PM »
will I be able to use my drive shaft from a 63/4 rear end with a 8" pinto rear end . I have a C-3 transmission. Thanks alot for help Tim.
Logged

Offline PintoMan1

  • Pinto Sr. Member
  • ****
  • Posts: 400
  • FeedBack: +0/-0
  • Gender: Male

    • Total Badges: 6
    Badges: (View All)
    Tenth year Anniversary Topic Starter Signature Poll Voter Windows User Fifth year Anniversary
Re: rear end swap
« Reply #1 on: December 23, 2013, 06:49:42 PM »
tim, I did the same swap with a 4spd. and had to shorten the shaft 1''. I'm not sure about and auto trans, but I don't see why you couldn't use your shaft for what you want to do. glen
Logged
1973 pinto runabout

Offline Wittsend

  • Pinto Master
  • *****
  • Posts: 2499
  • FeedBack: +241/-0

    • Total Badges: 8
    Badges: (View All)
    Tenth year Anniversary Mobile User Topic Starter Poll Voter 1000 Posts Linux User Windows User Fifth year Anniversary
Re: rear end swap
« Reply #2 on: December 24, 2013, 11:50:58 AM »
This is not the same setup as you have, but I went from a ('73) C-4 with a 6-3/4" to an '88 TC T-5 with a 8" and I did not need to change the shaft.  IF your C-3 is similar in length to the T-5 then it seems that it should work.
Logged

Offline junker

  • Pinto Member
  • **
  • Posts: 17
  • FeedBack: +1/-0
  • Another Pinto Driver

    • Total Badges: 2
    Badges: (View All)
    Topic Starter Windows User
Re: rear end swap
« Reply #3 on: December 24, 2013, 12:16:29 PM »
Thank you all for the help. Hoping all will work well. No drive shaft shops close and funds are in short demand. Merry Christmas to all.
Logged

Offline amc49

  • PCCA VIP
  • Pinto Master
  • ***
  • Posts: 1256
  • FeedBack: +242/-1
  • Another Pinto Driver

    • Total Badges: 4
    Badges: (View All)
    Topic Starter Poll Voter Windows User 1000 Posts
Re: rear end swap
« Reply #4 on: December 25, 2013, 01:33:02 AM »
Jack car up UNDER REAR AXLE TUBES with driveshaft installed. Make sure it can't roll on you. Mark or measure where installed driveshaft stub goes in trans right at the seal. Then pull back of driveshaft loose from rear end and then take shaft and slide it further in (too far) in back of trans till it hits softly and measure again and determine the difference in the two numbers. You need one inch firm to allow for in/out as the suspension works in normal use and that also guarantees the stub is in far enough. If less than one inch and you hit a really big bump or pothole, stub will go in far enough to knock out the stub end plug and kiss all your ATX fluid goodbye, you find out when trans locks up from no fluid in it.
Logged
Pages: [1]   Go Up
« previous next »