Current Classifieds

Front sway bar frame brackets
Date: 07/13/2017 01:05 am
Windshield
Date: 01/15/2022 09:31 pm
SEARCHING HOPELESSLY
Date: 02/02/2017 07:21 am
TWM Intake
Date: 08/15/2018 08:20 pm
windshield
Date: 04/14/2018 08:53 pm
Tubing bender 1/2 to 2 1/2 (3) inch roll cage / mufflers and more

Date: 03/13/2021 12:57 pm
76 drivers fender
Date: 07/20/2018 08:24 pm
1973 Pinto Wagon

Date: 05/06/2022 05:13 pm
Offenhauser 6114 dp
Date: 09/12/2017 10:26 pm
13x6 minilite style wheels MAKE OFFER——NEED GONE

Date: 08/01/2018 01:17 pm
Runabout rear window '73 to 80.
Date: 01/12/2019 10:19 am
1972 Runabout 351 Cleveland V8

Date: 11/05/2016 09:03 pm

« previous next »
Pages: [1]   Go Down

Author Topic: rear end swap  (Read 1725 times)

0 Members and 1 Guest are viewing this topic.

Offline junker

  • Pinto Member
  • **
  • Posts: 17
  • FeedBack: +1/-0
  • Another Pinto Driver

    • Total Badges: 2
    Badges: (View All)
    Topic Starter Windows User
rear end swap
« on: December 23, 2013, 01:54:59 PM »
will I be able to use my drive shaft from a 63/4 rear end with a 8" pinto rear end . I have a C-3 transmission. Thanks alot for help Tim.
Logged

Offline PintoMan1

  • Pinto Sr. Member
  • ****
  • Posts: 400
  • FeedBack: +0/-0
  • Gender: Male

    • Total Badges: 6
    Badges: (View All)
    Tenth year Anniversary Topic Starter Signature Poll Voter Windows User Fifth year Anniversary
Re: rear end swap
« Reply #1 on: December 23, 2013, 06:49:42 PM »
tim, I did the same swap with a 4spd. and had to shorten the shaft 1''. I'm not sure about and auto trans, but I don't see why you couldn't use your shaft for what you want to do. glen
Logged
1973 pinto runabout

Offline Wittsend

  • Pinto Master
  • *****
  • Posts: 2499
  • FeedBack: +241/-0

    • Total Badges: 8
    Badges: (View All)
    Tenth year Anniversary Mobile User Topic Starter Poll Voter 1000 Posts Linux User Windows User Fifth year Anniversary
Re: rear end swap
« Reply #2 on: December 24, 2013, 11:50:58 AM »
This is not the same setup as you have, but I went from a ('73) C-4 with a 6-3/4" to an '88 TC T-5 with a 8" and I did not need to change the shaft.  IF your C-3 is similar in length to the T-5 then it seems that it should work.
Logged

Offline junker

  • Pinto Member
  • **
  • Posts: 17
  • FeedBack: +1/-0
  • Another Pinto Driver

    • Total Badges: 2
    Badges: (View All)
    Topic Starter Windows User
Re: rear end swap
« Reply #3 on: December 24, 2013, 12:16:29 PM »
Thank you all for the help. Hoping all will work well. No drive shaft shops close and funds are in short demand. Merry Christmas to all.
Logged

Offline amc49

  • PCCA VIP
  • Pinto Master
  • ***
  • Posts: 1256
  • FeedBack: +242/-1
  • Another Pinto Driver

    • Total Badges: 4
    Badges: (View All)
    Topic Starter Poll Voter Windows User 1000 Posts
Re: rear end swap
« Reply #4 on: December 25, 2013, 01:33:02 AM »
Jack car up UNDER REAR AXLE TUBES with driveshaft installed. Make sure it can't roll on you. Mark or measure where installed driveshaft stub goes in trans right at the seal. Then pull back of driveshaft loose from rear end and then take shaft and slide it further in (too far) in back of trans till it hits softly and measure again and determine the difference in the two numbers. You need one inch firm to allow for in/out as the suspension works in normal use and that also guarantees the stub is in far enough. If less than one inch and you hit a really big bump or pothole, stub will go in far enough to knock out the stub end plug and kiss all your ATX fluid goodbye, you find out when trans locks up from no fluid in it.
Logged
Pages: [1]   Go Up
« previous next »