Current Classifieds

Looking for Radiator and gas tank
Date: 10/24/2018 07:35 am
72 pinto

Date: 06/23/2016 12:40 pm
Pinto Parts for sale
Date: 06/19/2017 02:01 pm
FREE PARTS!!

Date: 01/10/2017 02:38 pm
71-73 2.0 4 speed transmission wanted
Date: 09/06/2020 01:57 am
1973 Ford Pinto, Shift linkage for a/t and cross member
Date: 02/25/2017 08:45 pm
71/72 Pinto front end bushing kit
Date: 02/05/2017 09:45 am
71/72 Pinto front end bushing kit
Date: 02/05/2017 09:45 am
Need seals Pinto Wagon
Date: 02/16/2017 05:09 pm
76 pinto sedan sbc/bbc project for sale $1700 obo

Date: 03/27/2017 10:07 pm
Need 2.3 timing cover
Date: 08/10/2018 11:41 am
Runabout rear window '73 to 80.
Date: 01/12/2019 10:19 am

Author Topic: Rag Joint Steering replacement  (Read 3987 times)

0 Members and 1 Guest are viewing this topic.

Offline mrskydog

  • Pinto Full Member
  • ***
  • Posts: 246
  • FeedBack: +3/-0
  • Gender: Male
  • "Another Horse in the Stable"

  • Total Badges: 7
    Badges: (View All)
    Tenth year Anniversary Mobile User Topic Starter Signature Fifth year Anniversary Poll Voter Windows User
Rag Joint Steering replacement
« on: July 21, 2012, 07:24:18 PM »
Today I tackled the steering Rag Joint.
The ones on 79-80 were plastic and fall apart, bad design. Mine fell apart after 30 plus years. Took a total of about 3 hrs, I took my time. I will post pictures first, then I will follow up with what had to be done.
"Living the Dream...Drivin g Old Fords"
1965 Mustang 2+2 Fastback
1980 Pinto Rallye 32,000 Org.
1972 Maverick Grabber V-8 car
2005 Mustang

Offline mrskydog

  • Pinto Full Member
  • ***
  • Posts: 246
  • FeedBack: +3/-0
  • Gender: Male
  • "Another Horse in the Stable"

  • Total Badges: 7
    Badges: (View All)
    Tenth year Anniversary Mobile User Topic Starter Signature Fifth year Anniversary Poll Voter Windows User
Rag Joint Steering replacement
« Reply #1 on: July 21, 2012, 07:26:34 PM »
More pictures
"Living the Dream...Drivin g Old Fords"
1965 Mustang 2+2 Fastback
1980 Pinto Rallye 32,000 Org.
1972 Maverick Grabber V-8 car
2005 Mustang

Offline mrskydog

  • Pinto Full Member
  • ***
  • Posts: 246
  • FeedBack: +3/-0
  • Gender: Male
  • "Another Horse in the Stable"

  • Total Badges: 7
    Badges: (View All)
    Tenth year Anniversary Mobile User Topic Starter Signature Fifth year Anniversary Poll Voter Windows User
Re: Rag Joint Steering replacement
« Reply #2 on: July 21, 2012, 07:48:00 PM »
OK... 1st of all the car needs to be off the ground, ramps lift etc. The proper Part number for this is: Help Line Dorman Part# 31000. This Rag Joint is 2-1/4 inches
center bolt hole to bolt hole.  #1 remove coupler bolts at shaft. #2 remove upper shaft bolt at firewall. #3 Tap coupler at rack spline to loosen off shaft. #4 spray shaft upper with a good penetrating oil at slip spline. #5 sometimes need to tap upper shaft out of slip spline. see pictures of spline in vise,take car to mark your steering shaft ,have wheels straight. Drill out the 2 riveted post from lower coupler( in picture ) Bolt on Dorman Kit #31000 has instructions ,reused hardware with new bolts. #6 Loosen Rack front 2 bolts, and move rack forward to allow rebuilt shaft room to reinstall. #7 please note that the upper shaft at the firewall is (u-shaped) on on side at the end and must be installed matching this way. #8 Make sure to clean and lube shaft upper ,and lower rack spline. #8 Line up re tighten 2-rack bolts ,then all others. Drives like New! Hope this helps.....Kirk
"Living the Dream...Drivin g Old Fords"
1965 Mustang 2+2 Fastback
1980 Pinto Rallye 32,000 Org.
1972 Maverick Grabber V-8 car
2005 Mustang