Current Classifieds

Bumpers
Date: 07/06/2018 04:47 pm
Built 2.0
Date: 10/07/2018 05:27 pm
Mustang II V8 swap parts
Date: 03/26/2017 02:25 pm
2.3 pinto carb
Date: 08/18/2018 02:07 pm
'72 Runabout Drivers Side Door Hinge Set
Date: 12/15/2018 02:21 am
1973 Interior parts wanted
Date: 01/02/2017 11:02 pm
parting out 1975 & 80 pintos
Date: 10/31/2018 12:00 pm
1974 Pinto Right Rear Interior Trim Panel

Date: 02/18/2017 04:44 pm
hubcaps

Date: 05/13/2021 05:33 pm
1976 Pinto

Date: 10/24/2017 02:00 pm
rear hatch back louvers

Date: 04/18/2017 12:44 pm
door sills
Date: 03/14/2020 03:20 pm

« previous next »
Pages: [1]   Go Down

Author Topic: rad replacement  (Read 1279 times)

0 Members and 1 Guest are viewing this topic.

Offline shuffln

  • Pinto Member
  • **
  • Posts: 55
  • FeedBack: +7/-1
  • Another Pinto Driver

    • Total Badges: 4
    Badges: (View All)
    Topic Starter Linux User Mobile User Windows User
rad replacement
« on: August 19, 2015, 09:44:25 AM »
so i want to replace  my rad cause there is pin hole in and wanted to know what is the best. i'm not sure if i want to drop in my 289 or go 2.3 turbo.  would a V8 mustang II rad fit?   thanks
Logged

Offline 76hotrodpinto

  • Pinto Sr. Member
  • ****
  • Posts: 692
  • FeedBack: +13/-0
  • Gender: Male

    • Total Badges: 3
    Badges: (View All)
    Topic Starter Signature Windows User
Re: rad replacement
« Reply #1 on: August 19, 2015, 10:27:41 AM »
Yeah, the m2 radiator will fit. But if you have a pin hole, that's easily accessible, just solder it.
Logged
1976 half hatch 2.3 turbo w/t5.

Offline shuffln

  • Pinto Member
  • **
  • Posts: 55
  • FeedBack: +7/-1
  • Another Pinto Driver

    • Total Badges: 4
    Badges: (View All)
    Topic Starter Linux User Mobile User Windows User
Re: rad replacement
« Reply #2 on: August 19, 2015, 11:41:50 AM »
well i'm in luck then cause i have a 76 mustang II coupe that i'm parting out. so i guess i'll be taking a bunch of parts off and keeping for my bobcat.
Logged

Offline shuffln

  • Pinto Member
  • **
  • Posts: 55
  • FeedBack: +7/-1
  • Another Pinto Driver

    • Total Badges: 4
    Badges: (View All)
    Topic Starter Linux User Mobile User Windows User
Re: rad replacement
« Reply #3 on: August 28, 2015, 12:37:30 PM »
has anyone done a mustang II rad before if so what alterations did you do.  i don't think its a direct bolt and go.
Logged

Offline shuffln

  • Pinto Member
  • **
  • Posts: 55
  • FeedBack: +7/-1
  • Another Pinto Driver

    • Total Badges: 4
    Badges: (View All)
    Topic Starter Linux User Mobile User Windows User
Re: rad replacement
« Reply #4 on: September 02, 2015, 06:21:36 AM »
so anyone have a pic of the mustang II rad in your pinto/bobcat.  I have a mustang II v8 rad and just wondering how everyone installed them.
Logged
Pages: [1]   Go Up
« previous next »