Current Classifieds

79 pinto small parts
Date: 04/24/2019 03:16 pm
1978 Squire wagon 6 Cly
Date: 02/16/2020 05:42 pm
Wanted - 71-73 Pinto grill
Date: 12/15/2016 03:32 pm
76 pinto sedan sbc/bbc project for sale $1700 obo

Date: 03/27/2017 10:07 pm
1976 Ford Pinto

Date: 07/16/2019 02:51 am
1980 Pinto Wagon

Date: 02/29/2020 07:01 pm
Cruiser Dash Gauges
Date: 12/04/2016 11:50 am
Ford Speedometer Hall-Effect sensor with 6 foot speedometer cable

Date: 12/30/2022 01:30 pm
2.3/C-4 torque converter needed
Date: 02/08/2018 02:26 pm
Hood Hinge rubber boots
Date: 09/28/2018 05:49 pm
1973 Pinto Runabout

Date: 08/17/2022 06:27 pm
Plug Or Cover For Hatch Hinge Bolt For 1979
Date: 05/28/2017 03:20 pm

« previous next »
Pages: [1]   Go Down

Author Topic: Rack and Pinion rebuild  (Read 1582 times)

0 Members and 1 Guest are viewing this topic.

Offline pintolovr

  • Pinto Member
  • **
  • Posts: 91
  • FeedBack: +0/-0
  • Gender: Male

    • Total Badges: 8
    Badges: (View All)
    Topic Starter Signature Tenth year Anniversary Poll Voter Mobile User Apple User Windows User Fifth year Anniversary
Rack and Pinion rebuild
« on: November 23, 2013, 10:03:20 AM »
Wanting to rebuild a Rack and Pinion. Does anyone know hwhere to get a kit with seals and such? Thanks
Logged
1973 Pinto Cruising Wagon (5.0 H.O.)
1977 Cutlass Y-19 (sold)
1974 2.0 4 speed 42,000 miles

Offline 74 PintoWagon

  • Pinto Sr. Master
  • ******
  • Posts: 3105
  • FeedBack: +540/-0
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 5
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User 1000 Posts
Re: Rack and Pinion rebuild
« Reply #1 on: November 23, 2013, 10:24:53 AM »
Logged
Art
65 Falcon 2DR 200 IL6 with C4.

Offline amc49

  • PCCA VIP
  • Pinto Master
  • ***
  • Posts: 1256
  • FeedBack: +242/-1
  • Another Pinto Driver

    • Total Badges: 4
    Badges: (View All)
    Topic Starter Poll Voter Windows User 1000 Posts
Re: Rack and Pinion rebuild
« Reply #2 on: November 25, 2013, 10:21:45 PM »
Power or no?

If power be advised that it takes special tool to pull and install the hydraulic seal that goes on driver side next to the gears. Seal is at the end of say 12 inch long 2 inch diameter hydraulic bore that piston seats in meaning you cannot mar or scratch the bore at all or rack is junk. VERY hard to work within those confines, I did it but you have no idea there. If that seal seems useable I'd leave it in place, everything else is a piece of cake. Obvious that they use some sort of piloting specialty tool there to pull and install seals at the factory.

If you have to go there, luck, BTDT.
Logged

Offline 74 PintoWagon

  • Pinto Sr. Master
  • ******
  • Posts: 3105
  • FeedBack: +540/-0
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 5
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User 1000 Posts
Re: Rack and Pinion rebuild
« Reply #3 on: November 26, 2013, 07:09:37 AM »
Sounds like it be better to just get a reman??..
Logged
Art
65 Falcon 2DR 200 IL6 with C4.
Pages: [1]   Go Up
« previous next »