Current Classifieds

72 Pinto parts
Date: 12/04/2018 09:56 pm
Needed- Good 71-73 Rear End or parts- close to AL
Date: 09/15/2019 12:38 pm
2.3 bellhousing stick
Date: 07/24/2019 06:50 pm
instrument cluster,4sd trans crossmember,2.3 intake
Date: 08/26/2018 06:23 pm
73 rear hatchback glass
Date: 07/06/2017 11:33 am
2.8 Engine mount brackets
Date: 12/28/2016 11:42 am
GRILLE NEEDED '71,'72,'73 for a '73 Pinto
Date: 02/10/2017 09:30 am
Need seals Pinto Wagon
Date: 02/16/2017 05:09 pm
79-80 fenders, hood, rallye wheels, light buckets, etc, C3 trans
Date: 01/04/2017 04:07 am
74 Pinto Rear Side Lights

Date: 02/18/2017 05:47 pm
Wanted Dash for Pinto up to 1975
Date: 01/19/2020 09:06 am
Clutch pedal needed
Date: 01/11/2024 06:31 am

« previous next »
Pages: [1]   Go Down

Author Topic: pvc valve relocation  (Read 2245 times)

0 Members and 1 Guest are viewing this topic.

Offline stonhed18

  • Pinto Member
  • **
  • Posts: 21
  • FeedBack: +3/-0
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 4
    Badges: (View All)
    Topic Starter Apple User Mobile User Windows User
pvc valve relocation
« on: June 25, 2014, 11:04:53 AM »
Ok I've finally put my "new" cannon intake on my 2.3. however there is no connection for my pvc hose. Can I run it to a breather on the valve cover to the oil vapor separator?
 Any help would be greatly appreciated!
Logged

Offline 74 PintoWagon

  • Pinto Sr. Master
  • ******
  • Posts: 3105
  • FeedBack: +540/-0
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 5
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User 1000 Posts
Re: pvc valve relocation
« Reply #1 on: June 25, 2014, 11:16:58 AM »
No, a PCV valve needs to be connected to a vacuum source, should be a spot at the carb base I would think???..
Logged
Art
65 Falcon 2DR 200 IL6 with C4.

Offline stonhed18

  • Pinto Member
  • **
  • Posts: 21
  • FeedBack: +3/-0
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 4
    Badges: (View All)
    Topic Starter Apple User Mobile User Windows User
Re: pvc valve relocation
« Reply #2 on: June 25, 2014, 11:35:24 AM »
Thanks Wag :'(on! This where it was... can it be attached to the #1 runner with a proper fitting?
Logged

Offline 74 PintoWagon

  • Pinto Sr. Master
  • ******
  • Posts: 3105
  • FeedBack: +540/-0
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 5
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User 1000 Posts
Re: pvc valve relocation
« Reply #3 on: June 25, 2014, 11:37:40 AM »
Yes it can, you could also run your vacuum advance off that same fitting.. Looks like there's a fitting on there now?.
Logged
Art
65 Falcon 2DR 200 IL6 with C4.

Offline stonhed18

  • Pinto Member
  • **
  • Posts: 21
  • FeedBack: +3/-0
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 4
    Badges: (View All)
    Topic Starter Apple User Mobile User Windows User
Re: pvc valve relocation
« Reply #4 on: June 25, 2014, 12:10:07 PM »
Great! Thank you!  That fitting is too small but have one that will do the trick
Logged

Offline 74 PintoWagon

  • Pinto Sr. Master
  • ******
  • Posts: 3105
  • FeedBack: +540/-0
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 5
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User 1000 Posts
Re: pvc valve relocation
« Reply #5 on: June 25, 2014, 12:21:09 PM »
You're welcome, looks like you're good to go..
Logged
Art
65 Falcon 2DR 200 IL6 with C4.

Offline amc49

  • PCCA VIP
  • Pinto Master
  • ***
  • Posts: 1256
  • FeedBack: +242/-1
  • Another Pinto Driver

    • Total Badges: 4
    Badges: (View All)
    Topic Starter Poll Voter Windows User 1000 Posts
Re: pvc valve relocation
« Reply #6 on: June 25, 2014, 04:54:22 PM »
PCV entry should be in a PLENUM not individual runner, they always pass a bit of oil mist and not dispersing that to ALL cylinders can result in one plug oiling out pretty quick. Needs to be there as well for the straight air being mixed closer to equal in all cylinders, put it in only one and you can burn a piston from being too lean in that cylinder...... .not the way to do it............ ..
Logged

Offline 74 PintoWagon

  • Pinto Sr. Master
  • ******
  • Posts: 3105
  • FeedBack: +540/-0
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 5
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User 1000 Posts
Re: pvc valve relocation
« Reply #7 on: June 25, 2014, 06:07:25 PM »
Hmmm, good point that escaped me there, spacer under the carb would be the way to go, unless there's a spot to drill and tap for it??..
Logged
Art
65 Falcon 2DR 200 IL6 with C4.

Offline stonhed18

  • Pinto Member
  • **
  • Posts: 21
  • FeedBack: +3/-0
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 4
    Badges: (View All)
    Topic Starter Apple User Mobile User Windows User
Re: pvc valve relocation
« Reply #8 on: June 25, 2014, 08:23:15 PM »
Looks like Ill be making a spacer and tapping a fitting. Thank you for your wisdom!
Logged

Offline amc49

  • PCCA VIP
  • Pinto Master
  • ***
  • Posts: 1256
  • FeedBack: +242/-1
  • Another Pinto Driver

    • Total Badges: 4
    Badges: (View All)
    Topic Starter Poll Voter Windows User 1000 Posts
Re: pvc valve relocation
« Reply #9 on: June 27, 2014, 02:54:32 AM »
Or drill intake itself........ .....easy enough on most.......... ....
Logged
Pages: [1]   Go Up
« previous next »