Current Classifieds

upholstery for bucket seats
Date: 10/30/2018 08:44 am
Windshield
Date: 01/15/2022 09:31 pm
Free ford C3 transmission in 95695..
Date: 06/07/2021 08:14 pm
parting out 1975 & 80 pintos
Date: 04/28/2018 04:12 pm
McLeod Clutch

Date: 04/12/2017 12:08 pm
Windshield
Date: 01/15/2022 09:31 pm
Wanted Pinto Fiberglass Body Parts
Date: 05/19/2018 04:56 pm
1975 mercury bobcat

Date: 08/14/2018 03:40 pm
73 Runabout

Date: 11/20/2017 03:19 pm
78 hatchback

Date: 03/12/2023 06:50 pm
Looking for fan shroud for 72' Pinto 1.6
Date: 04/13/2017 04:56 am
1974 Pinto Right Rear Interior Trim Panel

Date: 02/18/2017 04:44 pm

Author Topic: Power to manual rack swap  (Read 1075 times)

0 Members and 1 Guest are viewing this topic.

Offline Darren Laih

  • Pinto Driver
  • *
  • Posts: 9
  • FeedBack: +0/-0
  • Gender: Male

  • Total Badges: 3
    Badges: (View All)
    Topic Starter Webmaster Mobile User
Power to manual rack swap
« on: June 25, 2016, 02:58:41 PM »
Quick question is the swap from power just a rack change and remove power steering pump or is it more involved?

Offline 72pair

  • Pinto Sr. Member
  • ****
  • Posts: 269
  • FeedBack: +56/-0
  • Gender: Male

  • Total Badges: 6
    Badges: (View All)
    Tenth year Anniversary Topic Starter Signature Poll Voter Windows User Fifth year Anniversary
Re: Power to manual rack swap
« Reply #1 on: June 25, 2016, 04:59:30 PM »
On my 80 Bobcat, I had to change tie rod ends and the rag joint coupling for the manual specific pieces.
72 sedan 2.0, c-4 beater now hot 2.0, 4-speed
72 sedan 2.3, t-5, 8" running project
80 Bobcat hatchback 2.3, 4-spd, 97K

Offline Darren Laih

  • Pinto Driver
  • *
  • Posts: 9
  • FeedBack: +0/-0
  • Gender: Male

  • Total Badges: 3
    Badges: (View All)
    Topic Starter Webmaster Mobile User
Re: Power to manual rack swap
« Reply #2 on: June 25, 2016, 08:44:35 PM »
Thanks for the input

Offline Rob3865

  • Pinto Full Member
  • ***
  • Posts: 202
  • FeedBack: +19/-2
  • Gender: Male
  • Another Pinto Driver

  • Total Badges: 5
    Badges: (View All)
    Mobile User Topic Starter Signature Poll Voter Windows User
Re: Power to manual rack swap
« Reply #3 on: June 28, 2016, 12:19:45 AM »
On my 80 Bobcat, I had to change tie rod ends and the rag joint coupling for the manual specific pieces.

I am doing the same thing. Would you mind sharing WHERE you found the manual rag joint? Thanks.

Offline 72pair

  • Pinto Sr. Member
  • ****
  • Posts: 269
  • FeedBack: +56/-0
  • Gender: Male

  • Total Badges: 6
    Badges: (View All)
    Tenth year Anniversary Topic Starter Signature Poll Voter Windows User Fifth year Anniversary
Re: Power to manual rack swap
« Reply #4 on: June 29, 2016, 04:02:04 PM »
I got lucky and found a pinto in my local pull a part. I was actually searching other fords for something with the same shaft/spline when I stumbled on the pinto.
72 sedan 2.0, c-4 beater now hot 2.0, 4-speed
72 sedan 2.3, t-5, 8" running project
80 Bobcat hatchback 2.3, 4-spd, 97K