Current Classifieds

Pinto interior parts for Cruisen / Rallye wagon
Date: 01/19/2021 03:56 pm
1978 Squire wagon 6 Cly
Date: 03/08/2021 10:44 am
Wagon hatch letters
Date: 12/31/2023 04:24 pm
hubcaps

Date: 10/31/2018 12:04 pm
74 Pinto Hub Caps & Trim Rings

Date: 02/28/2018 09:37 am
Drip rail chrome
Date: 01/14/2017 09:18 am
1980 Pinto w/ Trunk
Date: 08/10/2022 04:09 pm
77 Wagon rear hatch
Date: 12/04/2019 05:57 am
1.6 New Ford cylinder head with side draft carbs

Date: 06/12/2018 08:18 pm
79 pinto steering column
Date: 08/18/2018 02:00 pm
Gas Tank Sending Unit
Date: 05/22/2018 02:17 pm
77 Cruising wagon Rear cargo light
Date: 10/02/2017 02:16 pm

« previous next »
Pages: [1]   Go Down

Author Topic: Power to manual rack swap  (Read 1105 times)

0 Members and 1 Guest are viewing this topic.

Offline Darren Laih

  • Pinto Driver
  • *
  • Posts: 9
  • FeedBack: +0/-0
  • Gender: Male

    • Total Badges: 3
    Badges: (View All)
    Topic Starter Webmaster Mobile User
Power to manual rack swap
« on: June 25, 2016, 02:58:41 PM »
Quick question is the swap from power just a rack change and remove power steering pump or is it more involved?
Logged

Offline 72pair

  • Pinto Sr. Member
  • ****
  • Posts: 269
  • FeedBack: +56/-0
  • Gender: Male

    • Total Badges: 6
    Badges: (View All)
    Tenth year Anniversary Topic Starter Signature Poll Voter Windows User Fifth year Anniversary
Re: Power to manual rack swap
« Reply #1 on: June 25, 2016, 04:59:30 PM »
On my 80 Bobcat, I had to change tie rod ends and the rag joint coupling for the manual specific pieces.
Logged
72 sedan 2.0, c-4 beater now hot 2.0, 4-speed
72 sedan 2.3, t-5, 8" running project
80 Bobcat hatchback 2.3, 4-spd, 97K

Offline Darren Laih

  • Pinto Driver
  • *
  • Posts: 9
  • FeedBack: +0/-0
  • Gender: Male

    • Total Badges: 3
    Badges: (View All)
    Topic Starter Webmaster Mobile User
Re: Power to manual rack swap
« Reply #2 on: June 25, 2016, 08:44:35 PM »
Thanks for the input
Logged

Offline Rob3865

  • Pinto Full Member
  • ***
  • Posts: 202
  • FeedBack: +19/-2
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 5
    Badges: (View All)
    Mobile User Topic Starter Signature Poll Voter Windows User
Re: Power to manual rack swap
« Reply #3 on: June 28, 2016, 12:19:45 AM »
Quote from: 72pair on June 25, 2016, 04:59:30 PM
On my 80 Bobcat, I had to change tie rod ends and the rag joint coupling for the manual specific pieces.

I am doing the same thing. Would you mind sharing WHERE you found the manual rag joint? Thanks.
Logged

Offline 72pair

  • Pinto Sr. Member
  • ****
  • Posts: 269
  • FeedBack: +56/-0
  • Gender: Male

    • Total Badges: 6
    Badges: (View All)
    Tenth year Anniversary Topic Starter Signature Poll Voter Windows User Fifth year Anniversary
Re: Power to manual rack swap
« Reply #4 on: June 29, 2016, 04:02:04 PM »
I got lucky and found a pinto in my local pull a part. I was actually searching other fords for something with the same shaft/spline when I stumbled on the pinto.
Logged
72 sedan 2.0, c-4 beater now hot 2.0, 4-speed
72 sedan 2.3, t-5, 8" running project
80 Bobcat hatchback 2.3, 4-spd, 97K
Pages: [1]   Go Up
« previous next »