Current Classifieds

looking for 1978 pinto head rebuild kit
Date: 05/24/2020 08:19 am
free transmissions
Date: 11/28/2019 10:21 am
Instrument Panel with Tach wanted
Date: 05/15/2022 11:36 am
1977 Pinto Hatchback Parts

Date: 08/29/2020 05:31 pm
'80 Pinto Wagon
Date: 02/01/2018 05:20 pm
2.3 turbo intake (lower)

Date: 07/15/2020 09:29 pm
Right side strut mount for 3rd door 1979 runabout
Date: 10/04/2019 08:43 pm
1973 Pinto Runabout

Date: 03/25/2019 09:02 pm
Parts for 74 Squire Wagon
Date: 09/16/2019 07:35 pm
PINTO TRUNK LATCH & CATCH

Date: 03/23/2018 09:39 pm
t-5 2.3 trans and new flywheel cluch and pressure plate though out bearing for sale
Date: 09/09/2018 03:22 pm
1973 Pinto Runabout

Date: 03/25/2019 09:02 pm

« previous next »
Pages: [1]   Go Down

Author Topic: Port hole windows  (Read 1425 times)

0 Members and 1 Guest are viewing this topic.

Offline Jdm071755

  • Pinto Full Member
  • ***
  • Posts: 163
  • FeedBack: +24/-0
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 3
    Badges: (View All)
    Topic Starter Signature Mobile User
Port hole windows
« on: August 19, 2017, 03:00:02 PM »
I'm pretty sure these rings just pull out but I want to make sure. Since parts are so hard and expensive I just want to check.


Sent from my iPhone using Tapatalk
Logged
Joe

Offline Jdm071755

  • Pinto Full Member
  • ***
  • Posts: 163
  • FeedBack: +24/-0
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 3
    Badges: (View All)
    Topic Starter Signature Mobile User
Re: Port hole windows
« Reply #1 on: August 20, 2017, 04:55:28 PM »
Ok so I may be wrong I tried taking off the inside bezel by just pulling on it. It's not budging   Do I have to take the whole thing apart?


Sent from my iPhone using Tapatalk
Logged
Joe

Offline Pintopower

  • PCCA Management Board
  • Pinto Sr. Member
  • ******
  • Posts: 720
  • FeedBack: +92/-0
  • Gender: Male
  • Why a Pinto? Because I don't care what you think.
    • My Car Pictures

    • Total Badges: 10
    Badges: (View All)
    Topic Starter Signature Poll Voter Apple User Mobile User Photographer Windows User Webmaster Tenth year Anniversary Fifth year Anniversary
Re: Port hole windows
« Reply #2 on: August 21, 2017, 02:51:39 PM »
Hmmm, mine just pull out. I suspect that either they have been in there a million years and are stuck or someone siliconed them? are you able to use a denstist's tool to pry the rubber away from the trim ring a little bit?
Logged
I have many Pintos, I like them....
#1. 1979 Wagon V6 Restored
#2. 1977 Wagon V6 Restored
#3. 1980 Sedan I4 Original
#4. 1974 Pangra Wagon I4 Turbo
#5. 1980 Wagon I4 Restored
#6. 1976 Bobcat Squire Hatchback (Restoring)
...Like i said, I like them.
...and I have 4 Fiats.

Offline Jdm071755

  • Pinto Full Member
  • ***
  • Posts: 163
  • FeedBack: +24/-0
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 3
    Badges: (View All)
    Topic Starter Signature Mobile User
Re: Port hole windows
« Reply #3 on: August 21, 2017, 04:02:00 PM »
Good idea I will give it a try. I am just a little cautious because parts are so hard to find. Thanks so much


Sent from my iPhone using Tapatalk
Logged
Joe

Offline Jdm071755

  • Pinto Full Member
  • ***
  • Posts: 163
  • FeedBack: +24/-0
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 3
    Badges: (View All)
    Topic Starter Signature Mobile User
Re: Port hole windows
« Reply #4 on: August 24, 2017, 01:04:50 PM »
Quote from: Pintopower on August 21, 2017, 02:51:39 PM
Hmmm, mine just pull out. I suspect that either they have been in there a million years and are stuck or someone siliconed them? are you able to use a denstist's tool to pry the rubber away from the trim ring a little bit?
Thanks
What I did was put Dawn and water in a spry bottle. The sprayed the rubber seal and they came right out.


Sent from my iPhone using Tapatalk
Logged
Joe
Pages: [1]   Go Up
« previous next »