Current Classifieds

looking for parts
Date: 06/19/2020 02:32 pm
looking for 1978 pinto head rebuild kit
Date: 05/24/2020 08:19 am
1970-1973 Gas Tank/Blue Dash
Date: 02/07/2019 11:57 pm
NEED 77/78 MUSTANG II Left Motor Mount
Date: 04/15/2017 05:14 pm
Front Body parts needed
Date: 02/09/2018 06:09 pm
1973 Pinto Pangra

Date: 07/08/2019 10:09 pm
Chilton's Repair & Tune-up Guide 1971-1979 Pinto and Bobcat

Date: 03/06/2017 01:24 am
Wanted 1971-73 pinto 2.0 4 speed manual transmission
Date: 03/06/2019 06:40 pm
ISO instrument panel 80 hatchback
Date: 04/20/2017 08:56 pm
Radiator
Date: 05/27/2018 06:07 am
Ford 2.3 Bellhousing C4/C5 & Torque Converter

Date: 07/08/2022 11:51 pm
Mallory Unilight dist 2.0
Date: 10/25/2019 03:44 pm

« previous next »
Pages: [1]   Go Down

Author Topic: Port hole windows  (Read 1419 times)

0 Members and 1 Guest are viewing this topic.

Offline Jdm071755

  • Pinto Full Member
  • ***
  • Posts: 163
  • FeedBack: +24/-0
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 3
    Badges: (View All)
    Topic Starter Signature Mobile User
Port hole windows
« on: August 19, 2017, 03:00:02 PM »
I'm pretty sure these rings just pull out but I want to make sure. Since parts are so hard and expensive I just want to check.


Sent from my iPhone using Tapatalk
Logged
Joe

Offline Jdm071755

  • Pinto Full Member
  • ***
  • Posts: 163
  • FeedBack: +24/-0
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 3
    Badges: (View All)
    Topic Starter Signature Mobile User
Re: Port hole windows
« Reply #1 on: August 20, 2017, 04:55:28 PM »
Ok so I may be wrong I tried taking off the inside bezel by just pulling on it. It's not budging   Do I have to take the whole thing apart?


Sent from my iPhone using Tapatalk
Logged
Joe

Offline Pintopower

  • PCCA Management Board
  • Pinto Sr. Member
  • ******
  • Posts: 720
  • FeedBack: +92/-0
  • Gender: Male
  • Why a Pinto? Because I don't care what you think.
    • My Car Pictures

    • Total Badges: 10
    Badges: (View All)
    Topic Starter Signature Poll Voter Apple User Mobile User Photographer Windows User Webmaster Tenth year Anniversary Fifth year Anniversary
Re: Port hole windows
« Reply #2 on: August 21, 2017, 02:51:39 PM »
Hmmm, mine just pull out. I suspect that either they have been in there a million years and are stuck or someone siliconed them? are you able to use a denstist's tool to pry the rubber away from the trim ring a little bit?
Logged
I have many Pintos, I like them....
#1. 1979 Wagon V6 Restored
#2. 1977 Wagon V6 Restored
#3. 1980 Sedan I4 Original
#4. 1974 Pangra Wagon I4 Turbo
#5. 1980 Wagon I4 Restored
#6. 1976 Bobcat Squire Hatchback (Restoring)
...Like i said, I like them.
...and I have 4 Fiats.

Offline Jdm071755

  • Pinto Full Member
  • ***
  • Posts: 163
  • FeedBack: +24/-0
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 3
    Badges: (View All)
    Topic Starter Signature Mobile User
Re: Port hole windows
« Reply #3 on: August 21, 2017, 04:02:00 PM »
Good idea I will give it a try. I am just a little cautious because parts are so hard to find. Thanks so much


Sent from my iPhone using Tapatalk
Logged
Joe

Offline Jdm071755

  • Pinto Full Member
  • ***
  • Posts: 163
  • FeedBack: +24/-0
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 3
    Badges: (View All)
    Topic Starter Signature Mobile User
Re: Port hole windows
« Reply #4 on: August 24, 2017, 01:04:50 PM »
Quote from: Pintopower on August 21, 2017, 02:51:39 PM
Hmmm, mine just pull out. I suspect that either they have been in there a million years and are stuck or someone siliconed them? are you able to use a denstist's tool to pry the rubber away from the trim ring a little bit?
Thanks
What I did was put Dawn and water in a spry bottle. The sprayed the rubber seal and they came right out.


Sent from my iPhone using Tapatalk
Logged
Joe
Pages: [1]   Go Up
« previous next »