Current Classifieds

1972-1980 Pinto/Bobcat Wagon Drivers Side Tail Light OEM

Date: 04/20/2017 10:10 am
KYB shocks

Date: 02/08/2017 07:09 pm
74 Pinto Hub Caps & Trim Rings

Date: 02/18/2017 04:47 pm
2.0 Mickey Thompson SUPER RARE Rocker cover and belt guard
Date: 08/22/2017 09:21 pm
1971-1975 Pinto
Date: 01/09/2017 04:14 pm
ENGINE COMPLETE 1971 PINTO
Date: 12/28/2017 03:55 pm
Hatch needed
Date: 09/10/2017 09:16 pm
74 Driver side Wagon Fender, 74 driver side Door, Nice Wheels

Date: 09/15/2019 08:30 pm
1974 Pinto Passenger side door glass and door parts

Date: 02/18/2017 05:55 pm
Wheel cap
Date: 04/25/2022 11:21 pm
door sills
Date: 03/14/2020 03:20 pm
Weather Strip, Muffler, Splash Shields

Date: 02/21/2022 11:11 pm

« previous next »
Pages: [1]   Go Down

Author Topic: Point Gap and Fuel pume pressure  (Read 819 times)

0 Members and 1 Guest are viewing this topic.

Offline dennisofaz

  • Pinto Member
  • **
  • Posts: 98
  • FeedBack: +25/-0

    • Total Badges: 5
    Badges: (View All)
    Topic Starter Tenth year Anniversary Poll Voter Windows User Fifth year Anniversary
Point Gap and Fuel pume pressure
« on: February 28, 2018, 11:52:11 AM »
Hi, I have a 74 Runabout with a 2.3 and I need to know what the point gap souuld be, and what the fuel pump pressure should be.  Thank you in advance!


Dennis




Logged

Offline nnn0wqk

  • Pinto Member
  • **
  • Posts: 99
  • FeedBack: +24/-0
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 5
    Badges: (View All)
    Topic Starter Poll Voter Windows User Tenth year Anniversary Fifth year Anniversary
Re: Point Gap and Fuel pume pressure
« Reply #1 on: February 28, 2018, 02:36:31 PM »
Point gap is .027 with dwell reading of 35-41 degrees. Timing is 6 degrees BTDC vacuum hose disconnected at distributor. Idle 850 rpm standard 750 auto in Drive. Plugs AGRF-52 gap is .034. Fuel pump pressure between 3.5-4.5 lbs and volume would probably run around a pint in 20 seconds. Total timing advance should approach 47 degrees.  Base 6 degrees, centrifugal advance 32 degrees, vacuum 4.3 degrees. You should see total centrifugal at 4700 rpm. I pulled all this information out of a 1974 Motor auto repair manual. A little more information than you asked for but since I had the book open thought I might as well list it for you.
Logged

Offline dennisofaz

  • Pinto Member
  • **
  • Posts: 98
  • FeedBack: +25/-0

    • Total Badges: 5
    Badges: (View All)
    Topic Starter Tenth year Anniversary Poll Voter Windows User Fifth year Anniversary
Re: Point Gap and Fuel pume pressure
« Reply #2 on: February 28, 2018, 03:35:55 PM »
Hi nnn0wqk, Thank you very much for the information!  I will try a 4-7lb electric fuel pump and see how it goes!


Dennis 
Logged
Pages: [1]   Go Up
« previous next »