Current Classifieds

Wanted Dash for Pinto up to 1975
Date: 01/19/2020 09:06 am
WANTED: 1979 Bumper End Caps - Front and Rear
Date: 02/16/2019 10:46 am
Looking for license plate bracket, interior parts 72' Runabout
Date: 04/12/2017 08:15 am
Need '75 Pinto wagon front seat belt assembly housing
Date: 10/03/2018 10:46 pm
Clutch Cable Needed
Date: 04/03/2017 10:54 pm
Clutch Fork
Date: 03/31/2018 09:12 pm
Wanted Dash for Pinto up to 1975
Date: 01/19/2020 09:06 am
Front sway bar frame brackets
Date: 07/13/2017 01:05 am
EARLY PINTO CLUTCH PEDAL ASSEMBLY
Date: 02/14/2019 06:27 pm
74 4 spd and rear axle
Date: 09/26/2018 03:51 pm
6.6.75 carrier
Date: 02/14/2018 06:47 am
WTB Cruising Wagon
Date: 12/07/2016 05:35 pm

« previous next »
Pages: [1]   Go Down

Author Topic: Please help! Installing RAD B-1 4 sp in pinto from 74 Mustang II  (Read 1562 times)

0 Members and 1 Guest are viewing this topic.

Offline racinmud

  • Pinto Driver
  • *
  • Posts: 4
  • FeedBack: +0/-0
  • Another Pinto Driver

    • Total Badges: 1
    Badges: (View All)
    Topic Starter
Please help! Installing RAD B-1 4 sp in pinto from 74 Mustang II
« on: May 24, 2014, 05:08:24 PM »
Shelled the C3 and thought I would put in a 4 speed.  Found a 4 speed from a 74 Mustang 2.3,  finally found a flywheel and clutch.  Went to install today and after bolting it all together the throw out bearing won't engage pressure plate , not even close.  It is the D5 case and fork that came with the trans.     Took it all apart to make sure fork was on pivot ball and it was.  Any ideas?  Please help
Thanks, Leon       
Logged

Offline oldkayaker

  • Pinto Master
  • *****
  • Posts: 758
  • FeedBack: +114/-0
  • Gender: Male

    • Total Badges: 5
    Badges: (View All)
    Topic Starter Signature Windows User Tenth year Anniversary Fifth year Anniversary
Re: Please help! Installing RAD B-1 4 sp in pinto from 74 Mustang II
« Reply #1 on: May 25, 2014, 04:06:29 AM »
Just guessing that the throw out bearing is not reaching the clutch fingers.  From vague memory, the Mustang II 2.3 flywheel was at least a 1/2 " thicker than the Pinto 2.3 flywheel (looked ridiculously heavy).  If you used a Pinto 2.3 flywheel, it may not work without accommodating modifications.  Throw out bearings and pivot balls are available in different lengths.
Logged
Jerry J - Jupiter, Florida

Offline amc49

  • PCCA VIP
  • Pinto Master
  • ***
  • Posts: 1256
  • FeedBack: +242/-1
  • Another Pinto Driver

    • Total Badges: 4
    Badges: (View All)
    Topic Starter Poll Voter Windows User 1000 Posts
Re: Please help! Installing RAD B-1 4 sp in pinto from 74 Mustang II
« Reply #2 on: May 26, 2014, 03:45:58 PM »
Need the difference in flywheel thickness and add that to pivot ball length. Needs to be pretty close to get correct leverage and full travel of throwout. Or a longer /shorter throwoout bearing involved there.
Logged
Pages: [1]   Go Up
« previous next »