Current Classifieds

Looking for 1.6 exhaust manifold heat shield, front license plate bracket
Date: 11/04/2018 02:34 am
Wagon hatch letters
Date: 12/31/2023 04:24 pm
1980 Pinto Wagon

Date: 02/29/2020 07:01 pm
74 4 spd and rear axle
Date: 09/26/2018 03:51 pm
1977 Front Sump 2.3 Oil Pan
Date: 09/14/2018 11:42 pm
Mustang II C4 Transmission
Date: 07/28/2017 06:26 am
SVO SWAP
Date: 03/15/2018 03:12 am
Built 2.0
Date: 10/07/2018 05:27 pm
v8 springs
Date: 05/07/2017 04:46 pm
Looking for license plate bracket, interior parts 72' Runabout
Date: 04/12/2017 08:15 am
77 Wagon rear hatch
Date: 12/04/2019 05:57 am
1979 PINTO PARTS--FREE
Date: 09/13/2022 02:05 pm

Author Topic: Please advise...  (Read 458 times)

0 Members and 1 Guest are viewing this topic.

Offline Dtmix

  • Pinto Sr. Member
  • ****
  • Posts: 255
  • FeedBack: +7/-0
  • Gender: Male
  • Dan and the Orange Blossom (Pinto Squire Wagon)

  • Total Badges: 3
    Badges: (View All)
    Topic Starter Signature Mobile User
Please advise...
« on: July 07, 2021, 07:48:29 AM »
I just put up a post under my Pandemic project forum asking for advisement about my concerns regarding a ticking noise when engine is cold, and goes away once warmed up.  Please take a look at my question and advise...

I put this post up as I wanted to keep everything together under my Pandemic Project blog, but I was afraid some people who may have the answer might not be following my blog.  All of you guys are awesome with your suggestions and/or advisements...

Happy Motoring!
Dan
Happy Motoring!
Dan

Offline pinto_one

  • Pinto Master
  • *****
  • Posts: 1008
  • FeedBack: +70/-0
  • Gender: Male
  • Pinto-One

  • Total Badges: 10
    Badges: (View All)
    1000 Posts Photographer Tenth year Anniversary Topic Starter Signature Poll Voter Mobile User Apple User Windows User Fifth year Anniversary
Re: Please advise...
« Reply #1 on: July 07, 2021, 08:36:30 PM »
The ticking noise could be from one lifter if the noise is coming from the valve cover , sometimes over time a piece do sluge or some crud gets into them and they will bleed down and tick away until the oil pumps them up to take up the slack and the tick goes away , one you can remove them one by one and take them apart to clean the little check valve in them , do not mix up the parts , clean with a spray can of B-12 chem tool when you pull them apart , keep every thing clean when you have it apart , done this a few times on high mileage pintos that lacked needed oil changes , hope this helps
76 Pinto sedan V6 , 79 pinto cruiser wagon V6 soon to be diesel or 4.0

Offline HOSS429

  • Pinto Full Member
  • ***
  • Posts: 222
  • FeedBack: +22/-0
  • old ford guy

  • Total Badges: 5
    Badges: (View All)
    Tenth year Anniversary Fifth year Anniversary Topic Starter Poll Voter Windows User
Re: Please advise...
« Reply #2 on: July 08, 2021, 01:45:06 PM »
take a short piece of hose pipe and cup one end to your ear and wave the other end over the engine while it is making the noise and you may be able to pinpoint a reasonable location for the ticking .. as it goes away when the engine warms up  it may be an exhaust leak as well ..

Offline lugnut

  • Pinto Full Member
  • ***
  • Posts: 176
  • FeedBack: +14/-1
  • Gender: Male

  • Total Badges: 5
    Badges: (View All)
    Topic Starter Tenth year Anniversary Poll Voter Windows User Fifth year Anniversary
Re: Please advise...
« Reply #3 on: July 09, 2021, 08:42:01 PM »
Quite often an exhaust leak at the manifold will make a ticking noise until it heats up. Does the noise increase when the engine load is more?
mike