Current Classifieds

Wanted 73 pinto squire wagon
Date: 05/09/2020 11:59 am
Many Parts Listed Below
Date: 04/20/2018 11:15 am
4 speed pinto transmission

Date: 05/13/2021 05:29 pm
74 4 spd and rear axle
Date: 09/26/2018 03:51 pm
2.0 Mickey Thompson SUPER RARE Rocker cover and belt guard
Date: 08/22/2017 09:21 pm
74 Pinto Hub Caps & Trim Rings

Date: 02/28/2018 09:37 am
v8 springs
Date: 05/07/2017 04:46 pm
Various Pinto Parts 1971 - 1973

Date: 10/01/2020 02:00 pm
77-78 front grill
Date: 04/07/2017 12:35 am
Various Pinto Parts 1971 - 1973

Date: 10/01/2020 02:00 pm
1971 2 lt Cam
Date: 10/10/2020 06:27 pm
Clutch pedal needed
Date: 01/11/2024 06:31 am

Author Topic: Part Identification Help  (Read 1554 times)

0 Members and 1 Guest are viewing this topic.

Offline 1972 Wagon

  • Pinto Full Member
  • ***
  • Posts: 119
  • FeedBack: +27/-0
  • Gender: Female
  • 1972 Pinto Wagon

  • Total Badges: 4
    Badges: (View All)
    Fifth year Anniversary Mobile User Signature Topic Starter
Part Identification Help
« on: February 07, 2017, 12:57:12 PM »
Can someone identify this part? It is in a bundle of wires that run along the fire wall and end above the master cylinder. I have checked my books and can't find a picture. Thanks
*The Original Family Car: A 1972 Pinto Wagon*
Ordered by my folks from Bunnell Motor Company, Inc., Bunnell, Florida
Delivered: June 20, 1972
Entrusted to my care: August 1976

Offline robertwwithee

  • Pinto Full Member
  • ***
  • Posts: 228
  • FeedBack: +4/-0
  • Another Pinto Driver

  • Total Badges: 2
    Badges: (View All)
    Mobile User Topic Starter
Re: Part Identification Help
« Reply #1 on: February 08, 2017, 02:26:00 PM »
It's been awhile since I owned an automatic Pinto but I do remember a plug like that heading down to park/neutral safety switch.  Is car an auto or stick? If stick it might not be used.

Sent from my SPH-L720T using Tapatalk


Offline pinto_one

  • Pinto Master
  • *****
  • Posts: 1008
  • FeedBack: +70/-0
  • Gender: Male
  • Pinto-One

  • Total Badges: 10
    Badges: (View All)
    1000 Posts Photographer Tenth year Anniversary Topic Starter Signature Poll Voter Mobile User Apple User Windows User Fifth year Anniversary
Re: Part Identification Help
« Reply #2 on: February 08, 2017, 04:42:14 PM »
if she has a manual trans it could be the backup light switch , if it had more wires on it it would be an auto trans , but since it is unpluged the starter would not work , (unless it was bypassed )  way to check is to put the car in reverse and turn the key one and see if the backup lites work , if they do she might have A/C  and some had a kicker that speed up the engine when you turned on the A/C , most over the years have disepered  :o
76 Pinto sedan V6 , 79 pinto cruiser wagon V6 soon to be diesel or 4.0

Offline 1972 Wagon

  • Pinto Full Member
  • ***
  • Posts: 119
  • FeedBack: +27/-0
  • Gender: Female
  • 1972 Pinto Wagon

  • Total Badges: 4
    Badges: (View All)
    Fifth year Anniversary Mobile User Signature Topic Starter
Re: Part Identification Help
« Reply #3 on: February 08, 2017, 06:45:24 PM »
The car is an automatic with factory installed A/C. The backup lights work. I had not driven the car for many years and finally got it back on the road. I can't remember if the connector was like that in years past. My 90 year old dad (original owner) can't remember what it was for either. I figure someone else might have a better memory!
*The Original Family Car: A 1972 Pinto Wagon*
Ordered by my folks from Bunnell Motor Company, Inc., Bunnell, Florida
Delivered: June 20, 1972
Entrusted to my care: August 1976

Offline pinto_one

  • Pinto Master
  • *****
  • Posts: 1008
  • FeedBack: +70/-0
  • Gender: Male
  • Pinto-One

  • Total Badges: 10
    Badges: (View All)
    1000 Posts Photographer Tenth year Anniversary Topic Starter Signature Poll Voter Mobile User Apple User Windows User Fifth year Anniversary
Re: Part Identification Help
« Reply #4 on: February 08, 2017, 07:06:37 PM »
Ok then it has to be kicker , it's for when you turn on the A/C it speeds up the engine (or keeps it from dying) a tad , you have to use a volt meter to test it to find out , when the A/C clutch is engaged you should have voltage on one of the wires , been years since I have seen one , the newer ones used vacuum to do the same thing , hope this helps , Later   Blane in Mississippi 😇
76 Pinto sedan V6 , 79 pinto cruiser wagon V6 soon to be diesel or 4.0

Offline robertwwithee

  • Pinto Full Member
  • ***
  • Posts: 228
  • FeedBack: +4/-0
  • Another Pinto Driver

  • Total Badges: 2
    Badges: (View All)
    Mobile User Topic Starter
Re: Part Identification Help
« Reply #5 on: February 08, 2017, 07:34:20 PM »
Ur right, more likely back up switch.

Sent from my SPH-L720T using Tapatalk