Current Classifieds

1974 Ford Pinto Squire Wagon

Date: 05/30/2020 01:51 pm
1978 Squire wagon 6 Cly
Date: 03/08/2021 10:44 am
13x6 minilite style wheels MAKE OFFER——NEED GONE

Date: 08/01/2018 01:17 pm
need intake for oval port 2.3l
Date: 08/22/2018 09:23 am
Interior Parts
Date: 08/07/2017 03:59 pm
72 pinto drag car

Date: 07/08/2017 08:53 pm
I need a 1976 hood
Date: 12/19/2016 06:02 pm
99' 2.5l lima cylinder head

Date: 01/13/2017 01:56 am
1971 yellow Pinto hatchback with limited edition chrome strips on rear door, 1600 cc engine

Date: 02/26/2017 03:22 pm
1972 Runabout 351 Cleveland V8

Date: 11/05/2016 09:03 pm
'79 Ford Pinto, Green,

Date: 10/29/2019 11:50 am
Clutch Cable Needed
Date: 04/03/2017 11:03 pm

Author Topic: Oil Pump Drive??  (Read 2297 times)

0 Members and 2 Guests are viewing this topic.

Offline Trucker Tim

  • Pinto Member
  • **
  • Posts: 74
  • FeedBack: +2/-0
  • Gender: Male
  • TRUCKER TIM

  • Total Badges: 3
    Badges: (View All)
    Topic Starter Signature Windows User
Oil Pump Drive??
« on: August 28, 2014, 07:45:51 AM »
Hello Crew.
  Can someone tell me what part of the 2.3 actually drives the oil pump?? If the timing belt is removed or broken will the oil pump spin?? I'm starting to think I should have do a bit more research on this project.  Thank You In Advance.
"All that is necessary for the triumph of evil
is that good men do nothing."

Offline bbobcat75

  • Pinto Master
  • *****
  • Posts: 1032
  • FeedBack: +71/-0
  • Gender: Male

  • Total Badges: 9
    Badges: (View All)
    Tenth year Anniversary Topic Starter Signature Poll Voter 1000 Posts Apple User Mobile User Windows User Fifth year Anniversary
Re: Oil Pump Drive??
« Reply #1 on: August 28, 2014, 07:53:51 AM »
YES THE OIL PUMP IS DRIVEN BY THE TIMING BELT - THE AUX. DRIVE PULLEY DRIVES THE OIL PUMP AND DIST.
1975 mercury bobcat 2.8 auto
1978 mercury bobcat wagon 2.3l - soon to have a 88 tc drive line - SOLD - 🙁
1975 ford pinto - drag car - 2.3l w/t5 trans - project car

Offline Trucker Tim

  • Pinto Member
  • **
  • Posts: 74
  • FeedBack: +2/-0
  • Gender: Male
  • TRUCKER TIM

  • Total Badges: 3
    Badges: (View All)
    Topic Starter Signature Windows User
Re: Oil Pump Drive??
« Reply #2 on: August 28, 2014, 08:58:45 AM »
Thank You Very Much bbobcat75!
  That answers why the new oil filter was still dry after pulling the vehicle around in gear spinning the motor.
  My father had a "Bobcat" for years! 
"All that is necessary for the triumph of evil
is that good men do nothing."

Offline amc49

  • PCCA VIP
  • Pinto Master
  • ***
  • Posts: 1256
  • FeedBack: +242/-1
  • Another Pinto Driver

  • Total Badges: 4
    Badges: (View All)
    Topic Starter Poll Voter Windows User 1000 Posts
Re: Oil Pump Drive??
« Reply #3 on: August 28, 2014, 09:41:46 AM »
Gee, I sure hope you didn't tear up something doing that, I had a guy who we built a super 440 Magnum motor for that then insisted on towing car to try to start it when his new engine startup skills were lacking, it tore up the cam lobes and put metal dust all in the engine and it had to be totally rebuilt before it even fired up once. Pretty dang sad, that one was. Couldn't trust him after that to start it, I had to go over and get it running for him on the second one. The guy was an engineer to boot. A '70 Charger nut, he had like 5 of them. One was 426 Hemi too but his tuneup skills were like the others and it was a dog too.

Offline Trucker Tim

  • Pinto Member
  • **
  • Posts: 74
  • FeedBack: +2/-0
  • Gender: Male
  • TRUCKER TIM

  • Total Badges: 3
    Badges: (View All)
    Topic Starter Signature Windows User
Re: Oil Pump Drive??
« Reply #4 on: August 28, 2014, 09:47:49 AM »
Hello AMC49.
  I hope I didn't screw myself, but at this point in the project I just needed to see if anything would move at all. I didn't pull it very far or fast. Most of the time the transmission was in natural so I could work the front and rear ends.
  If I did any damage it's on me! (more time than brains)
"All that is necessary for the triumph of evil
is that good men do nothing."

Offline Pinto5.0

  • Pinto Master
  • *****
  • Posts: 1974
  • FeedBack: +77/-0
  • Gender: Male
  • 80 hatch, 76 Wagon, 72 & 73 Sedans, 71 half hatch

  • Total Badges: 7
    Badges: (View All)
    Topic Starter Signature Poll Voter Mobile User Fifth year Anniversary Windows User 1000 Posts
Re: Oil Pump Drive??
« Reply #5 on: August 28, 2014, 09:56:48 AM »
Find a junk distributor & grind the teeth off the lower gear & weld a short piece of 1/2" steel rod where the rotor used to be & chuck it up to a drill & run it till you have oil pressure
'73 Sedan (I'll get to it)
'76 Wagon driver
'80 hatch(Restoring to be my son's 1st car)~Callisto
'71 half hatch (bucket list Pinto)~Ghost
'72 sedan 5.0/T5~Lemon Squeeze

Offline Trucker Tim

  • Pinto Member
  • **
  • Posts: 74
  • FeedBack: +2/-0
  • Gender: Male
  • TRUCKER TIM

  • Total Badges: 3
    Badges: (View All)
    Topic Starter Signature Windows User
Re: Oil Pump Drive??
« Reply #6 on: August 28, 2014, 07:22:02 PM »
Well Crew, we have some oil pump action.
  Didn't have an old distributer shaft to use but did manage to turn the gear on the front of the motor that runs the pump & distributor with a right angle 3/8 air ratchet. Oil came spewing out of the port where you install the oil filter. (oil filter had been removed) As soon as I saw oil I stopped turning the gear.
  Belt install tomorrow. Wish me luck.   
"All that is necessary for the triumph of evil
is that good men do nothing."

Offline 74 PintoWagon

  • Pinto Sr. Master
  • ******
  • Posts: 3105
  • FeedBack: +540/-0
  • Gender: Male
  • Another Pinto Driver

  • Total Badges: 5
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User 1000 Posts
Re: Oil Pump Drive??
« Reply #7 on: August 28, 2014, 09:16:50 PM »
Now put a filter on and spin it until you see oil flowing up on top of the head for full lubrication..
Art
65 Falcon 2DR 200 IL6 with C4.

Offline Trucker Tim

  • Pinto Member
  • **
  • Posts: 74
  • FeedBack: +2/-0
  • Gender: Male
  • TRUCKER TIM

  • Total Badges: 3
    Badges: (View All)
    Topic Starter Signature Windows User
Re: Oil Pump Drive??
« Reply #8 on: August 29, 2014, 06:59:15 AM »
Excellent Idea "74 PintoWagon".
  Will give that a try this morning.

  On another note. Please excuse me if I have posted a few of my comments in the wrong section. I see there is a spot (Your Project) might be more appropriate for projects like my "Pinto" motor in a "Jeep". I'll put further posts in that section.
  And last but not least what a great bunch of Guys with outstanding knowledge and help.
"All that is necessary for the triumph of evil
is that good men do nothing."