Current Classifieds

Rally spoiler wanted
Date: 05/04/2017 01:32 pm
Mustang II V8 swap parts
Date: 03/26/2017 02:25 pm
76 pinto sedan sbc/bbc project for sale $1700 obo

Date: 10/27/2018 03:30 pm
Want seals for Pinto wagon "flip out" windows
Date: 08/08/2017 01:44 pm
1980 Ford Pinto For Sale

Date: 07/01/2018 03:21 pm
oldskool787
Date: 02/12/2017 12:42 pm
Holley 4bbl carb. & Offenhauser intake.

Date: 08/09/2018 07:49 am
76 Pinto Wagon
Date: 07/08/2020 05:44 pm
1972 Rallye wagon rebuild
Date: 11/14/2020 07:31 pm
1971-74 Various Pinto Parts
Date: 01/18/2020 03:44 pm
1979 Pinto Rear Bumper
Date: 03/26/2021 03:26 pm
upholstery for bucket seats
Date: 10/30/2018 08:44 am

Author Topic: Oil pan gasket  (Read 1444 times)

0 Members and 1 Guest are viewing this topic.

boughtabobcat

  • Guest
Oil pan gasket
« on: August 15, 2015, 06:10:59 PM »
Okay, have a question - I need to replace the oil pan gasket on my 78 Bobcat wagon, 2.3l auto. Is there a way I can do it without having to pull the engine? I was hoping I could just raise it a few inches with a cherry picker or hoist without having to remove the engine to get around that pesky lower crossmember - anyone tried a method like that?

Offline 76hotrodpinto

  • Pinto Sr. Member
  • ****
  • Posts: 692
  • FeedBack: +13/-0
  • Gender: Male

  • Total Badges: 3
    Badges: (View All)
    Topic Starter Signature Windows User
Re: Oil pan gasket
« Reply #1 on: August 15, 2015, 06:48:31 PM »
I don't think it can be done in car. The cross member and the oil pick-up tube would make it very hard. I think by time you barely clear it, you'll have only an engine on a chain, so might as well raise it the other 3 feet and do it more comfortably.

  I could be wrong though. There are some very crafty folks here.
1976 half hatch 2.3 turbo w/t5.

Offline pinto_one

  • Pinto Master
  • *****
  • Posts: 1008
  • FeedBack: +70/-0
  • Gender: Male
  • Pinto-One

  • Total Badges: 10
    Badges: (View All)
    1000 Posts Photographer Tenth year Anniversary Topic Starter Signature Poll Voter Mobile User Apple User Windows User Fifth year Anniversary
Re: Oil pan gasket
« Reply #2 on: August 15, 2015, 08:35:54 PM »
Done it before , you have to drop the rack by thanking the long bolts out , pull it forward a tad around a inch and a half , leave the steering shaft hooked up , toe in both wheels , after you put the car on some good Jack stands , remove the starter , then remove the long left and right motor mount bolts , jack up the engine untel the mounts are around two inches above the mount , then put back in the long motor mount bolts , lower the engine , the bolt will rest on top of the body mount pad , remove the Jack and unbolt the pan , make sure you drain the pan or you will be the first to find out you didn't,  with the pan removed check the oil pump pick up for trash, or being bent ,  if your pan is bent most of the time the pickup is too, it takes about two hours to do the job , but that was with a lift at the ford dealer I worked for , around three on your back with no air tools , good luck
76 Pinto sedan V6 , 79 pinto cruiser wagon V6 soon to be diesel or 4.0

Offline 76hotrodpinto

  • Pinto Sr. Member
  • ****
  • Posts: 692
  • FeedBack: +13/-0
  • Gender: Male

  • Total Badges: 3
    Badges: (View All)
    Topic Starter Signature Windows User
Re: Oil pan gasket
« Reply #3 on: August 15, 2015, 10:08:38 PM »
That's good to know. I wouldn't have thought it would clear with only a few inches.
1976 half hatch 2.3 turbo w/t5.