Current Classifieds

1975 Pinto bumpers
Date: 01/20/2018 07:51 pm
Need flywheel for 73 2.0 engine.
Date: 10/05/2017 02:26 pm
Gas Tank Sending Unit
Date: 05/22/2018 02:17 pm
73 actuator for heater blend door
Date: 09/19/2019 04:43 pm
Intake manifolds

Date: 03/06/2021 03:04 pm
Many Parts Listed Below
Date: 04/20/2018 11:15 am
Cruiser Dash Gauges
Date: 12/04/2016 11:50 am
Mint Original Black Rear Seat $275.00

Date: 07/30/2020 11:45 am
71-73 2.0 4 speed transmission wanted
Date: 09/06/2020 01:57 am
Drivers side door panel Orange
Date: 05/22/2018 01:54 pm
Looking for Passenger side Inner Fender Apron
Date: 10/28/2018 08:45 am
1973 Ford Pinto, Shift linkage for a/t and cross member
Date: 02/25/2017 08:45 pm

Author Topic: Need help with some parts  (Read 953 times)

0 Members and 1 Guest are viewing this topic.

Offline sxb0044

  • Pinto Driver
  • *
  • Posts: 3
  • FeedBack: +0/-0
  • Another Pinto Driver

  • Total Badges: 2
    Badges: (View All)
    Topic Starter Windows User
Need help with some parts
« on: September 06, 2015, 06:32:53 PM »
I have always been fascinated with anything Ford.  I came across a Pinto Station wagon with production date of 10/75 (presumably a 76').  The 5th digit in the VIN was a Y.  The vehicle has some goodies; including, air conditioning, powering steering. 

The Compressor bracket had an engineering number of D4ZH-2882-AB.  The alternator/smog pump?? had eng number D5ZE-10039-AA.  The power steering pump brackets (2) did not have any part number associated with same. 

Can anyone tell me if these parts were used on just Pintos or other Ford/Mercury makes/models, engine sizes and years? 

 

Offline sxb0044

  • Pinto Driver
  • *
  • Posts: 3
  • FeedBack: +0/-0
  • Another Pinto Driver

  • Total Badges: 2
    Badges: (View All)
    Topic Starter Windows User
Re: Need help with some parts
« Reply #1 on: September 06, 2015, 07:07:07 PM »
I have added a photo of the engine bay as I was thinking that the engine may have not been original to the vehicle. 

Offline pinto_one

  • Pinto Master
  • *****
  • Posts: 1007
  • FeedBack: +70/-0
  • Gender: Male
  • Pinto-One

  • Total Badges: 10
    Badges: (View All)
    1000 Posts Photographer Tenth year Anniversary Topic Starter Signature Poll Voter Mobile User Apple User Windows User Fifth year Anniversary
Re: Need help with some parts
« Reply #2 on: September 06, 2015, 08:48:04 PM »
They were also used on bobcats and mustang II with the 2.8 , after 79 the 2.8 was not an option anymore and the A/C compressors changed later , here is a photo of mine with all the stuff hooked up ,
76 Pinto sedan V6 , 79 pinto cruiser wagon V6 soon to be diesel or 4.0

Offline sxb0044

  • Pinto Driver
  • *
  • Posts: 3
  • FeedBack: +0/-0
  • Another Pinto Driver

  • Total Badges: 2
    Badges: (View All)
    Topic Starter Windows User
Re: Need help with some parts
« Reply #3 on: September 07, 2015, 12:26:12 AM »
Thanks for the reply.  It appears that the engine that I photographed would have been swapped out at some point given that the VIN was a "y' code which would have been the 2.3 4 cylinder? Am I correct. Or, was a/c braket, alternator/smog pump bracket the same for both the 6 cyl and 4 cylinder vehicles?