Current Classifieds

2.3 pinto carb
Date: 08/18/2018 02:07 pm
Built and Injected early 2000cc Engine

Date: 04/10/2017 07:30 pm
GRILLE NEEDED '71,'72,'73 for a '73 Pinto
Date: 02/10/2017 09:30 am
Need 72 pinto parts!
Date: 06/14/2019 01:40 pm
1979 Runabout Rear Panel
Date: 01/04/2020 02:03 pm
Want side to side luggage rack rails for '75 Pinto wagon
Date: 08/30/2018 12:59 am
Windshield
Date: 01/15/2022 09:31 pm
74 & Up Parts
Date: 01/20/2021 03:22 pm
74 hood
Date: 07/03/2017 03:46 pm
hood for a 79-80
Date: 11/30/2018 10:55 pm
parts needed
Date: 02/20/2017 07:58 am
1971 2 lt Cam
Date: 10/10/2020 06:27 pm

Author Topic: Need help with a new radiator mount  (Read 1796 times)

0 Members and 1 Guest are viewing this topic.

Offline Turbo_Pinto_77

  • Pinto Driver
  • *
  • Posts: 6
  • FeedBack: +0/-0
  • Gender: Male
  • Another Pinto Driver

  • Total Badges: 2
    Badges: (View All)
    Topic Starter Fifth year Anniversary
Need help with a new radiator mount
« on: December 27, 2011, 06:44:27 PM »
I'm looking to upgrade the radiator in my 77 Pinto this winter. The car has a 78 Buick 3.8 V6 with a turbo. The guy that put the motor in it custom built a radiator support and it has a Chrysler single row radiator in it right now. In the hot weather the car runs at around 205 degrees... It will touch 220 if I sit in any traffic. Too hot for my liking. I want to put in a 3 or 4 row aluminum radiator. The way the Chrysler one is mounted in the car now is by a rail down each side (tanks are on the top and bottom) There is no "tray" or anything at the bottom to sit a radiator in and I cant seem to find an aluminum radiator that is the same dimensions as my current one.

So, obviously I'm going to have to start from scratch on a new mounting design for a new aluminum radiator. Does anyone have a fairly clean and easy way to mount a radiator in my Pinto?

Should I just buy a Mustang or similar radiator and design the mount around the radiator?

What have the V-8 Pinto owners done to satisfy their cooling needs?

Thanks!

Offline Starliner

  • Pinto Sr. Member
  • ****
  • Posts: 409
  • FeedBack: +16/-0
  • Gender: Male

  • Total Badges: 5
    Badges: (View All)
    Topic Starter Signature Tenth year Anniversary Poll Voter Fifth year Anniversary
Re: Need help with a new radiator mount
« Reply #1 on: December 29, 2011, 11:48:14 AM »
First... Wow I would like to hear more about your "Grand National Pinto!"
 
Since the 6 cylinder should set back you should have a lot of room for many radiator and electric fan choices.
I would suggest first checking out a 77-78 Mustang II V8 radiator.  I would guess that it would drop in and be an easy installation.
Then add an electric fan with a shroud.   
1973 Pinto 1600 - Sold!  
1979 Pinto 2300 - Sold!
1984 Audi 5000 Avant - 60,000 original miles
1987 Audi 5000 S Quattro - The snowmobile
1973 Volvo 1800 ES wagon -  my project car
1976 Mustang II - Wifey's new toy

RSM

  • Guest
Re: Need help with a new radiator mount
« Reply #2 on: December 29, 2011, 12:28:55 PM »
I have a radiator for a Mustang II and it mounts different than the Pinto radiator. I was going to use one like that for my car but didn't have the room. I wound up with a custom radiator and mounted it inside of the radiator support. I did this so I could retain the hood latch...I hate hood pins. I'll wind up modifying the hood latch support so I can fit an electric fan to the front of the radiator since there is no room on the back side. I think I remember the post about your car. How much room do you have between the radiator and the front of the engine?? Here is a link to a forum where I posted a pic of what I did. http://www.route66wingsandwheels.com/viewtopic.php?f=3&t=3293&start=25