Current Classifieds

71-71 speedo cable
Date: 07/31/2021 09:04 pm
Looking for front seats
Date: 08/10/2021 09:54 pm
1974 Ford Pinto Squire Wagon

Date: 05/30/2020 01:51 pm
2.3 engine mounts,glove box parts,emblems,hatch,doors,hinges etc
Date: 08/26/2018 06:35 pm
I need a 1976 hood
Date: 12/19/2016 06:02 pm
1978 fuel sendng unit
Date: 05/27/2020 09:54 am
1979 Pinto Rear Bumper
Date: 03/26/2021 03:26 pm
79 pinto driveshaft
Date: 08/18/2018 02:03 pm
1979 Pinto Sedan Delivery

Date: 06/15/2019 03:30 pm
Odds and Ends 1976-77 Pinto Wagon

Date: 07/17/2019 05:23 pm
72 PINTO WAGON

Date: 09/23/2018 06:16 pm
MISC PINTO PARTS

Date: 08/27/2017 10:23 am

Author Topic: Question About cowl  (Read 9582 times)

0 Members and 1 Guest are viewing this topic.

Offline BlueGoldPinto

  • Pinto Sr. Member
  • ****
  • Posts: 334
  • FeedBack: +9/-0
  • Not Just Another Pinto Driver

  • Total Badges: 5
    Badges: (View All)
    Topic Starter Signature Poll Voter Tenth year Anniversary Fifth year Anniversary
Re: Question About cowl
« Reply #30 on: July 11, 2005, 06:37:13 PM »
All you need is a new windshield seal? <-------------JEALOUS!!!!! >:( ;)
My theory on the Gas Tank of the Ford Pinto:
If it ain't fixed, don't break it!! :)

Offline sagesunrise

  • Pinto Sr. Member
  • ****
  • Posts: 257
  • FeedBack: +2/-0
  • Gender: Female
  • Got Pinto?
    • sagesunrise

  • Total Badges: 8
    Badges: (View All)
    Topic Starter Signature Poll Voter Tenth year Anniversary Windows User Webmaster Fifth year Anniversary Photographer
Re: Question About cowl
« Reply #31 on: October 30, 2012, 02:56:38 PM »
I know it's been a while, but I have a leak issue. I had my pinto restored frame up in 2004. Has had a leak since. Yesterday, finally got a new windshield and gasket installed. Stopped one leak that was dripping on the passenger floorboards, even to where the dash hits the post. Now, it has a smaller leak on both sides that seems to be coming from the firewall. I am thinking it's some sort of seal that was never installed correctly, or was installed but it was already wore out when installed. Due to it leaking right out of the shop I doubt it is rusty cowl issues. Does anyone have any advice on this? If there is a seal under the dash/along the firewall somewhere, that is where I'd like to start. Thanks in advance :)
 
Also, I purchased my new front windshield gasket (for my '71 Pinto) off ebay from http://myworld.ebay.com/weatherstrip-specialists. Excellent quality product if anyone needs one. I paid under $100 for it and the place that installed the windshield even commented at the quality of the gasket. Hope that info helps someone keep their pinto dry.
Tiffany Morrison
'71 Pinto Sedan 2.0, '51 Willys CJ3A, '75 Ford F250, '70 Ford Maverick, '68 GMC Value Van (aka the Hippie Van), and a 1947 Flxible Clipper RV conversion Bus, 1953 Ford Jubilee Tractor, 1969 VW Baja Bug

Offline Pinto5.0

  • Pinto Master
  • *****
  • Posts: 1974
  • FeedBack: +77/-0
  • Gender: Male
  • 80 hatch, 76 Wagon, 72 & 73 Sedans, 71 half hatch

  • Total Badges: 7
    Badges: (View All)
    Topic Starter Signature Poll Voter Mobile User Fifth year Anniversary Windows User 1000 Posts
Re: Question About cowl
« Reply #32 on: October 30, 2012, 03:08:45 PM »
If its on the firewall it could be coming in around the heater motor or hoses, steering column, wire harness grommet or cables. There's a few potential leaky spots.
'73 Sedan (I'll get to it)
'76 Wagon driver
'80 hatch(Restoring to be my son's 1st car)~Callisto
'71 half hatch (bucket list Pinto)~Ghost
'72 sedan 5.0/T5~Lemon Squeeze

Offline sagesunrise

  • Pinto Sr. Member
  • ****
  • Posts: 257
  • FeedBack: +2/-0
  • Gender: Female
  • Got Pinto?
    • sagesunrise

  • Total Badges: 8
    Badges: (View All)
    Topic Starter Signature Poll Voter Tenth year Anniversary Windows User Webmaster Fifth year Anniversary Photographer
Re: Question About cowl
« Reply #33 on: October 30, 2012, 03:10:00 PM »
I need to take the time to check those areas. I suspect some grommets/gaskets were either never installed or installed in bad shape. Thanks for reading :) It's not a bad leak, but any leak at all sucks big time. 8)
Tiffany Morrison
'71 Pinto Sedan 2.0, '51 Willys CJ3A, '75 Ford F250, '70 Ford Maverick, '68 GMC Value Van (aka the Hippie Van), and a 1947 Flxible Clipper RV conversion Bus, 1953 Ford Jubilee Tractor, 1969 VW Baja Bug

Offline TIGGER

  • PCCA Charter Member
  • Pinto Master
  • *
  • Posts: 2422
  • FeedBack: +70/-0
  • Gender: Male

  • Total Badges: 10
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User Apple User Mobile User 1000 Posts Tenth year Anniversary Fifth year Anniversary Photographer
Re: Question About cowl
« Reply #34 on: October 30, 2012, 03:26:38 PM »
Check the seam sealer around the pinch welds all along the cowl.  On my crusing wagon, it had dried and flaked off.  I re-seam sealed all along there and under the fenders and my small leaks went away.
79 4cyl Wagon
73 Turbo HB
78 Cruising Wagon (sold 8/6/11)

Offline beaner

  • Pinto Full Member
  • ***
  • Posts: 138
  • FeedBack: +16/-0

  • Total Badges: 5
    Badges: (View All)
    Tenth year Anniversary Topic Starter Poll Voter Windows User Fifth year Anniversary
Re: Question About cowl
« Reply #35 on: October 30, 2012, 06:31:51 PM »
wiper posts?
 
brad :)