Current Classifieds

Looking for a few parts - TIA
Date: 02/19/2023 12:18 pm
76 pinto sedan sbc/bbc project for sale $1700 obo

Date: 10/27/2018 03:30 pm
4 speed pinto transmission

Date: 05/13/2021 05:29 pm
71-73 sway bar
Date: 06/12/2021 10:12 am
Right side strut mount for 3rd door 1979 runabout
Date: 10/04/2019 08:43 pm
76 Pinto Wagon
Date: 07/08/2020 05:44 pm
Seeking reveal molding for driver's door for a 1980 Squire Wagon
Date: 11/08/2020 02:10 pm
1974 Pinto Passenger side door glass and door parts

Date: 02/28/2018 09:18 am
2.3 pinto carb
Date: 08/18/2018 02:07 pm
1971 Pinto 5.0L

Date: 12/02/2017 12:23 am
Early Rare Small window hatch
Date: 08/16/2017 08:26 am
New front rotors and everything for '74-'80
Date: 08/02/2019 04:18 pm

« previous next »
Pages: [1]   Go Down

Author Topic: floors  (Read 1420 times)

0 Members and 1 Guest are viewing this topic.

Offline joe the troll

  • Pinto Driver
  • *
  • Posts: 2
  • FeedBack: +0/-0
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 1
    Badges: (View All)
    Topic Starter
floors
« on: January 19, 2014, 02:15:58 PM »
i know mustang II floors will fit the front with some small modifying but i cant figure out what to use for the rear floors . Or dos anyone know some one that can make a one pice front to rear floor pans? for a 1979 pinto cruiser wagon     thanks
Logged

Offline JohnW

  • Pinto Full Member
  • ***
  • Posts: 229
  • FeedBack: +5/-0
  • Gender: Male
  • 1980 Runabout

    • Total Badges: 4
    Badges: (View All)
    Topic Starter Signature Fifth year Anniversary Poll Voter
Re: floors
« Reply #1 on: January 20, 2014, 01:49:58 PM »
I don't think there's anything available. Find a shop that has a bead roller and have them make you some up out of some sheetmetal.
Logged
-

Offline waldo786

  • Pinto Full Member
  • ***
  • Posts: 236
  • FeedBack: +0/-0
  • Gender: Male

    • Total Badges: 5
    Badges: (View All)
    Tenth year Anniversary Topic Starter Poll Voter Windows User Fifth year Anniversary
Re: floors
« Reply #2 on: January 25, 2014, 08:21:50 PM »
How bad are the floors?  Are they rusted the whole way down?  Typically the area that is raised a bit for the seat doesn't rust out.  I had a 66 Mustang where that middle part was ok but the rest in the front and back were all rusted out.  I made patches and welded them in and it was fine.  That's most likely what you'll have to end up doing because I don't think there is anyone out there making reproduction floor pieces like for other cars like Mustangs, Firebirds and Camaros, etc.  I would use galvanized steel myself.
Logged

Offline TIGGER

  • PCCA Charter Member
  • Pinto Master
  • *
  • Posts: 2424
  • FeedBack: +70/-0
  • Gender: Male

    • Total Badges: 10
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User Apple User Mobile User 1000 Posts Tenth year Anniversary Fifth year Anniversary Photographer
Re: floors
« Reply #3 on: January 27, 2014, 12:43:01 PM »
On my 78 crusing wagon, I had to replace the pass side floor pan,. front and rear.  I cut some rust free panels from a doner car.  I would maybe try that route before making them.  Someone has to be parting out a car.  I will have to check but I might have one rear section from a 72 parts car I scrapped out a few years back.  I will have to check.
Logged
79 4cyl Wagon
73 Turbo HB
78 Cruising Wagon (sold 8/6/11)
Pages: [1]   Go Up
« previous next »