Current Classifieds

Front sway bar frame brackets
Date: 07/13/2017 01:05 am
Needed:73 Pinto center console/change tray
Date: 12/09/2018 11:35 pm
WTB. Seat cover or material LFront
Date: 07/01/2019 03:17 pm
Wanted: Oil Breather F0ZZ6A485A "87-8 from 2.3L Turbo
Date: 08/06/2021 02:23 pm
1973 Pinto Runabout

Date: 08/17/2022 06:27 pm
need intake for oval port 2.3l
Date: 08/22/2018 09:23 am
Need lower control arms for 1973 pinto
Date: 02/27/2017 10:10 pm
convert to stick
Date: 05/19/2018 09:26 pm
1977 Cruiser
Date: 06/29/2019 06:28 am
v8 springs
Date: 05/07/2017 04:46 pm
1974 Pinto Passenger side door glass and door parts

Date: 02/28/2018 09:18 am
72' hatchback parts wanted
Date: 08/25/2019 02:57 am

Author Topic: My '79 Pony Needs a Intake/Carb Update. Help.  (Read 1595 times)

0 Members and 1 Guest are viewing this topic.

Offline Natedawg63

  • Pinto Driver
  • *
  • Posts: 5
  • FeedBack: +0/-0
  • Another Pinto Driver

  • Total Badges: 4
    Badges: (View All)
    Topic Starter Mobile User Apple User Windows User
My '79 Pony Needs a Intake/Carb Update. Help.
« on: May 18, 2015, 09:16:54 AM »
I picked up a 1-owner Pony this past weekend and did lots of general maintenance on her. Alabama is not a smog State, so the smog pump is gone. Got her finished Sunday and seems the alternator is also shot... would not keep my brand new battery charged :(

The factory 2-barrel is shot... the little linkage on the butterfly valve is non functional and it is jus generally shot from sitting for years w/o running.

I want to replace the intake and carb, but nothing high-performance since I am gonna drop in a turbo or V8 at some point soon.

I jus want a setup that does not use 30 yards of vacuum tubes like the '79 does. I guess I need a pre-smog era intake carb but this is my first Pinto... so I am not up to snuff on what to look for. Any help is greatly accepted. Need to get her up and running :)

Thanks!
Nate

Offline Natedawg63

  • Pinto Driver
  • *
  • Posts: 5
  • FeedBack: +0/-0
  • Another Pinto Driver

  • Total Badges: 4
    Badges: (View All)
    Topic Starter Mobile User Apple User Windows User
Re: My '79 Pony Needs a Intake/Carb Update. Help.
« Reply #1 on: May 18, 2015, 11:48:42 AM »
Are '71-'74 2.0 single side draft carb intakes worth fooling with? Looking for a 2.0 so I can use a decent Weber carb or other early 2bbl carb w/o all the pollution crapola.

Thanks!

Offline Pintocrazed

  • Pinto Full Member
  • ***
  • Posts: 208
  • FeedBack: +24/-1
  • Gender: Male
  • Another Pinto Driver

  • Total Badges: 5
    Badges: (View All)
    Topic Starter Poll Voter Windows User Apple User Mobile User
Re: My '79 Pony Needs a Intake/Carb Update. Help.
« Reply #2 on: May 18, 2015, 12:22:47 PM »
ARE you putting it on a 2.0?

Offline amc49

  • PCCA VIP
  • Pinto Master
  • ***
  • Posts: 1256
  • FeedBack: +242/-1
  • Another Pinto Driver

  • Total Badges: 4
    Badges: (View All)
    Topic Starter Poll Voter Windows User 1000 Posts
Re: My '79 Pony Needs a Intake/Carb Update. Help.
« Reply #3 on: May 18, 2015, 02:56:57 PM »
Different engine, the intakes do not fit.

Unless the car is a California car with feedback carb the carb can be rigged exactly like an earlier one. The carb IS a Weber, just after Holley and Motorcraft got through with it. You're not smart enough to turbo or V-8 if you cannot figure out how to rig to drop the vacuum lines. No insult intended at all but the truth of it.

If no hi-perf parts then you are limited to the stock intake. You have a 2.3 motor in that car and a better motor than 2.0 in my view. Of course I will get some flak on that.

Offline Natedawg63

  • Pinto Driver
  • *
  • Posts: 5
  • FeedBack: +0/-0
  • Another Pinto Driver

  • Total Badges: 4
    Badges: (View All)
    Topic Starter Mobile User Apple User Windows User
Re: My '79 Pony Needs a Intake/Carb Update. Help.
« Reply #4 on: May 18, 2015, 06:19:24 PM »
Found what I needed on the Ranger Station. Thanks for the replies and the concern of my skills level :)