Current Classifieds

C-3 automatic transmission

Date: 08/17/2022 10:18 am
Racing seats
Date: 10/24/2019 09:41 pm
Pinto Vinyl Top

Date: 10/09/2020 10:29 pm
1979 hatch needed
Date: 05/13/2018 08:52 pm
Misc pinto parts 71-73 2.0
Date: 05/05/2020 11:56 pm
Wanted Pinto Fiberglass Body Parts
Date: 05/19/2018 04:56 pm
Pinto or Bobcat wagon wanted
Date: 08/05/2018 10:49 pm
WTB 1974 or 1975 Pinto Grille and Turn Signals
Date: 04/08/2018 05:47 pm
1979 Pinto Rear Bumper
Date: 03/26/2021 03:26 pm
pintos for sale
Date: 12/11/2018 04:29 pm
Mallory Unilight dist 2.0
Date: 10/25/2019 03:44 pm
Chilton's Repair & Tune-up Guide 1971-1979 Pinto and Bobcat

Date: 03/06/2017 01:24 am

« previous next »
Pages: [1]   Go Down

Author Topic: Maximum revs for stock 2.0 rods.  (Read 769 times)

0 Members and 1 Guest are viewing this topic.

Offline LongTimeFordMan

  • PCCA VIP
  • Pinto Sr. Member
  • ***
  • Posts: 450
  • FeedBack: +182/-0
  • Gender: Male
  • 1973 Red Pinto Wagon

    • Total Badges: 6
    Badges: (View All)
    Fifth year Anniversary Topic Starter Signature Windows User Linux User Mobile User
Maximum revs for stock 2.0 rods.
« on: May 07, 2018, 10:54:47 PM »
Hi.. well I just got the sidedraft manifold done and am testing it on my stock  engine and getting ready to install my new engine.

The new engine is basically stock rebuild new bearings, oil pump, pistons,etc
Factory 4 speed
 .060 overbore
Stock rods
Forged stock low compression pistons down in the hole.
Head milled .040
Mild cam 272 degrees .430 lift
Pertronix ignition
Dual SU HIF carburetors.
3.40 rear gears
14 inch tires
Cruises on fwy at 3000 rpm.at 70 mph

 The goal is to optomize for daily driver street use with emphasis on fuel economy, hence the SU carbs which can get 30-32 mpg on an 1800 cc mgb.

Not interested in racing the car except for occasional fwy driving.

My question is how many revs will the factory rods handle safely.  As I mentioned in my previous post about the SU carbs, with the carbs and factory cam I can easily rev to 5000 plus but have not been exceeding 5500.

I assume that with the cam and compression upgrades to the new engine, revs of 6000 plus are probably possible.  I have seen posts that the factory rods are "ok" to 6000 rpm.

Any opinions about more than that..
Logged
Red 1973 pinto wagon DD, SoCal desert car, Factory 4 speed, 3.40 gears, Stock engine, 14" rims and tires, 60 K original miles

Offline dick1172762

  • Vintage Pinto Racer
  • PCCA Management Board
  • Pinto Sr. Master
  • ******
  • Posts: 2623
  • FeedBack: +362/-0
  • Gender: Male
  • I'm a llama!

    • Total Badges: 7
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User 1000 Posts Tenth year Anniversary Fifth year Anniversary
Re: Maximum revs for stock 2.0 rods.
« Reply #1 on: May 08, 2018, 10:33:17 AM »
I ran 7000 rpm time after time in my 72 Pinto road race / autocross boy racer with a STOCK short block.  I x-rayed the rods at work and that's all. I do not think a stock 2.0L will do 7000 rpm with out a good cam and carbs.
Logged
Its better to be a has-been, than a never was.

Offline LongTimeFordMan

  • PCCA VIP
  • Pinto Sr. Member
  • ***
  • Posts: 450
  • FeedBack: +182/-0
  • Gender: Male
  • 1973 Red Pinto Wagon

    • Total Badges: 6
    Badges: (View All)
    Fifth year Anniversary Topic Starter Signature Windows User Linux User Mobile User
Re: Maximum revs for stock 2.0 rods.
« Reply #2 on: May 08, 2018, 10:48:02 AM »
Thanks dick..

I sort of figured the rods would be ok for 6000 but just wanted some peace of mind..

Years ago i had a capri with radical 2.0 with isky cam and 390 cfm holley 4bbl that i ran on the street in so cal for 4 years and it did 7000 with shot peened stock rods.

Did you by chance see the pix of  the manifold I built for the SU carbs?
Logged
Red 1973 pinto wagon DD, SoCal desert car, Factory 4 speed, 3.40 gears, Stock engine, 14" rims and tires, 60 K original miles
Pages: [1]   Go Up
« previous next »