Current Classifieds

Anyone scrapping a 1980
Date: 03/13/2020 08:46 pm
1971 2.0 valve cover
Date: 01/25/2019 07:09 pm
2.3/C-4 torque converter needed
Date: 02/08/2018 02:26 pm
72 pinto drag car

Date: 07/08/2017 08:53 pm
1974 Pinto Drivers door glass and parts

Date: 02/18/2017 05:52 pm
Looking for a 1980 windshield
Date: 07/30/2020 04:51 pm
turbo 4 cyl and aod trans
Date: 12/14/2019 04:55 pm
ISO instrument panel 80 hatchback
Date: 04/20/2017 08:56 pm
'78 Pinto Windshield Trim
Date: 05/09/2017 10:46 am
72 pinto and 88 turbo coupe

Date: 06/09/2016 04:13 am
1976 Pinto runabout

Date: 03/28/2017 08:14 pm
73 2.0 Timing Crank Gear & Woodruff key WANTED
Date: 09/01/2017 07:52 am

Author Topic: Manual to automatic questions  (Read 754 times)

0 Members and 1 Guest are viewing this topic.

Offline vikingsandpintos

  • Pinto Driver
  • *
  • Posts: 1
  • FeedBack: +0/-0

  • Total Badges: 2
    Badges: (View All)
    Topic Starter Fifth year Anniversary
Manual to automatic questions
« on: August 13, 2017, 11:07:42 AM »

I have a 79 Pinto with the 2.3 and 4 speed manual trans. I want to switch it to an automatic. I am getting too old to shift all the time! lol  I took it to a cruise last night, and it is a pain in really slow stop and go cruise traffic.


It is not really a daily driver, but part of that is because I have grown to dislike the clutch. I think if I put an auto in it, I would be more prone to drive it more often.


What all do I need to change to the auto? I know the normal such as the flywheel, and shifter, ect. And I'll need a trans cooler and lines, I don't think my rad has a cooler in it so would prob just add a separate cooler.  I have a couple of Pinto wagons around the same year at storage, I think one had a good trans. Will my current driveshaft work? I didn't know if the yoke and trans length were the same. I assume the wagon one is prob longer than my 2 door? Speedo hook up the same? Trans crossmember? Or is there anything else to watch for that I haven't thought of? Thanks!

Offline dick1172762

  • Vintage Pinto Racer
  • PCCA Management Board
  • Pinto Sr. Master
  • ******
  • Posts: 2623
  • FeedBack: +362/-0
  • Gender: Male
  • I'm a llama!

  • Total Badges: 7
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User 1000 Posts Tenth year Anniversary Fifth year Anniversary
Re: Manual to automatic questions
« Reply #1 on: August 13, 2017, 11:27:42 AM »
Sounds like you already know what you need. The drive shaft is different than a stick shift. You may be able to use an automatic drive shaft from a wagon, but it may need shorting some. And if you change yokes to an automatic yoke, the stock drive shaft may work. I've done this swap, but from an automatic to a stick shift. Cross member, spedo cable, etc all fit just fine, but the spedo gear in the tranie may need changing due to its number of teeth being different.
Its better to be a has-been, than a never was.

Offline blink77

  • Pinto Full Member
  • ***
  • Posts: 216
  • FeedBack: +7/-0
  • Gender: Male

  • Total Badges: 6
    Badges: (View All)
    Topic Starter Poll Voter Tenth year Anniversary Apple User Windows User Fifth year Anniversary
Re: Manual to automatic questions
« Reply #2 on: August 13, 2017, 12:15:45 PM »
Make sure to remove pilot bearing!!!!!

Offline dick1172762

  • Vintage Pinto Racer
  • PCCA Management Board
  • Pinto Sr. Master
  • ******
  • Posts: 2623
  • FeedBack: +362/-0
  • Gender: Male
  • I'm a llama!

  • Total Badges: 7
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User 1000 Posts Tenth year Anniversary Fifth year Anniversary
Re: Manual to automatic questions
« Reply #3 on: August 13, 2017, 12:19:10 PM »
Make sure to remove pilot bearing!!!!!
  RIGHT ON!
Its better to be a has-been, than a never was.