Current Classifieds

Holley 4bbl carb. & Offenhauser intake.

Date: 08/09/2018 07:49 am
KYB shocks

Date: 02/08/2017 07:09 pm
ford pinto door panels
Date: 03/20/2022 07:51 pm
79-80 full glass hatch

Date: 01/04/2017 04:04 am
1971 Pinto Do It Yourself Manual

Date: 03/06/2017 01:19 am
rear hatch back louvers

Date: 04/18/2017 12:44 pm
79 pinto front,rear alum bumpers

Date: 07/17/2018 09:49 pm
Pinto wagon Parts
Date: 06/23/2021 03:25 pm
1980 Pinto Parts

Date: 08/05/2020 04:20 pm
1972 Pinto SCCA BS race car

Date: 10/23/2018 04:01 pm
1979 Pinto 3-door Runabout *PRICE REDUCED*

Date: 01/21/2023 04:19 pm
Wanted: Oil Breather F0ZZ6A485A "87-8 from 2.3L Turbo
Date: 08/06/2021 02:23 pm

Author Topic: Manual to automatic questions  (Read 757 times)

0 Members and 1 Guest are viewing this topic.

Offline vikingsandpintos

  • Pinto Driver
  • *
  • Posts: 1
  • FeedBack: +0/-0

  • Total Badges: 2
    Badges: (View All)
    Topic Starter Fifth year Anniversary
Manual to automatic questions
« on: August 13, 2017, 11:07:42 AM »

I have a 79 Pinto with the 2.3 and 4 speed manual trans. I want to switch it to an automatic. I am getting too old to shift all the time! lol  I took it to a cruise last night, and it is a pain in really slow stop and go cruise traffic.


It is not really a daily driver, but part of that is because I have grown to dislike the clutch. I think if I put an auto in it, I would be more prone to drive it more often.


What all do I need to change to the auto? I know the normal such as the flywheel, and shifter, ect. And I'll need a trans cooler and lines, I don't think my rad has a cooler in it so would prob just add a separate cooler.  I have a couple of Pinto wagons around the same year at storage, I think one had a good trans. Will my current driveshaft work? I didn't know if the yoke and trans length were the same. I assume the wagon one is prob longer than my 2 door? Speedo hook up the same? Trans crossmember? Or is there anything else to watch for that I haven't thought of? Thanks!

Offline dick1172762

  • Vintage Pinto Racer
  • PCCA Management Board
  • Pinto Sr. Master
  • ******
  • Posts: 2623
  • FeedBack: +362/-0
  • Gender: Male
  • I'm a llama!

  • Total Badges: 7
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User 1000 Posts Tenth year Anniversary Fifth year Anniversary
Re: Manual to automatic questions
« Reply #1 on: August 13, 2017, 11:27:42 AM »
Sounds like you already know what you need. The drive shaft is different than a stick shift. You may be able to use an automatic drive shaft from a wagon, but it may need shorting some. And if you change yokes to an automatic yoke, the stock drive shaft may work. I've done this swap, but from an automatic to a stick shift. Cross member, spedo cable, etc all fit just fine, but the spedo gear in the tranie may need changing due to its number of teeth being different.
Its better to be a has-been, than a never was.

Offline blink77

  • Pinto Full Member
  • ***
  • Posts: 216
  • FeedBack: +7/-0
  • Gender: Male

  • Total Badges: 6
    Badges: (View All)
    Topic Starter Poll Voter Tenth year Anniversary Apple User Windows User Fifth year Anniversary
Re: Manual to automatic questions
« Reply #2 on: August 13, 2017, 12:15:45 PM »
Make sure to remove pilot bearing!!!!!

Offline dick1172762

  • Vintage Pinto Racer
  • PCCA Management Board
  • Pinto Sr. Master
  • ******
  • Posts: 2623
  • FeedBack: +362/-0
  • Gender: Male
  • I'm a llama!

  • Total Badges: 7
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User 1000 Posts Tenth year Anniversary Fifth year Anniversary
Re: Manual to automatic questions
« Reply #3 on: August 13, 2017, 12:19:10 PM »
Make sure to remove pilot bearing!!!!!
  RIGHT ON!
Its better to be a has-been, than a never was.