Current Classifieds

Need Interior Panels
Date: 07/09/2018 04:59 pm
1979 Pinto Sedan Delivery

Date: 06/15/2019 03:30 pm
t-5 2.3 trans and new flywheel cluch and pressure plate though out bearing for sale
Date: 09/09/2018 03:22 pm
need 1978 pinto guage cluster
Date: 03/07/2021 07:35 am
Wanted: automatic transmission shifter
Date: 07/21/2017 11:49 am
WTB: Factory air cleaner and fan shroud 1971 2.0
Date: 02/05/2020 11:06 am
77 Caliper Bolt
Date: 08/21/2018 04:02 pm
Misc pinto parts 71-73 2.0
Date: 05/05/2020 11:56 pm
1979 hatch needed
Date: 05/13/2018 08:52 pm
Brake rotors
Date: 03/24/2017 09:02 pm
79 pinto front,rear alum bumpers

Date: 07/17/2018 09:49 pm
1971 yellow Pinto hatchback with limited edition chrome strips on rear door, 1600 cc engine

Date: 02/26/2017 03:22 pm

« previous next »
Pages: [1]   Go Down

Author Topic: Lower ball joint help needed  (Read 2272 times)

0 Members and 1 Guest are viewing this topic.

Offline lightning

  • Pinto Member
  • **
  • Posts: 12
  • FeedBack: +0/-0
  • Gender: Male

    • Total Badges: 2
    Badges: (View All)
    Topic Starter Signature
Lower ball joint help needed
« on: July 06, 2014, 05:08:17 PM »
My 78 wagon is a REAL bubba special. Bubba replaced lower BJ with uppers. Do the lowers go up through the arm or bolt on top?

Thx in advance.





Logged
Using Tapatalk

Offline enzo

  • Pinto Member
  • **
  • Posts: 74
  • FeedBack: +0/-0
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 5
    Badges: (View All)
    Mobile User Fifth year Anniversary Topic Starter Poll Voter Windows User
Re: Lower ball joint help needed
« Reply #1 on: July 06, 2014, 07:42:27 PM »
WOW. Not sure that is even possible.  Not sure if the pin taper is the same on both, as well the length and diameter!
Then there is the fact that the top b/j has 3 bolts the same size of each other, and, the lower has 4 bolts - 2 different
size of the other 2.  Has the lower control arm been modified?, cut?, and rewelded?  But, to answer your original
question, from the bottom.
Logged

Offline amc49

  • PCCA VIP
  • Pinto Master
  • ***
  • Posts: 1256
  • FeedBack: +242/-1
  • Another Pinto Driver

    • Total Badges: 4
    Badges: (View All)
    Topic Starter Poll Voter Windows User 1000 Posts
Re: Lower ball joint help needed
« Reply #2 on: July 06, 2014, 11:46:59 PM »
If bolted on top nothing holds the rubber seal down.......... .............. ..
Logged

Offline lightning

  • Pinto Member
  • **
  • Posts: 12
  • FeedBack: +0/-0
  • Gender: Male

    • Total Badges: 2
    Badges: (View All)
    Topic Starter Signature
Re: Lower ball joint help needed
« Reply #3 on: July 07, 2014, 12:58:34 AM »
The pin taper and length is diff. I had a "rattle" in the front end because it wasn't tight. 2 of the bolt holes lined up (enough for Bubba). ;(

Logged
Using Tapatalk

Offline amc49

  • PCCA VIP
  • Pinto Master
  • ***
  • Posts: 1256
  • FeedBack: +242/-1
  • Another Pinto Driver

    • Total Badges: 4
    Badges: (View All)
    Topic Starter Poll Voter Windows User 1000 Posts
Re: Lower ball joint help needed
« Reply #4 on: July 07, 2014, 07:08:45 PM »
'... replaced lower BJ with uppers.'

Whoa I totally misread that one, thought you meant all 4 got changed. My bad.

Can't get much more bubba than that.......... ..
Logged

Offline lightning

  • Pinto Member
  • **
  • Posts: 12
  • FeedBack: +0/-0
  • Gender: Male

    • Total Badges: 2
    Badges: (View All)
    Topic Starter Signature
Re: Lower ball joint help needed
« Reply #5 on: July 08, 2014, 03:01:27 PM »
Is this correct?

Logged
Using Tapatalk

Offline amc49

  • PCCA VIP
  • Pinto Master
  • ***
  • Posts: 1256
  • FeedBack: +242/-1
  • Another Pinto Driver

    • Total Badges: 4
    Badges: (View All)
    Topic Starter Poll Voter Windows User 1000 Posts
Re: Lower ball joint help needed
« Reply #6 on: July 08, 2014, 07:24:36 PM »
Could easily be, hoping the bottom flange is showing simply because you have barely threaded bolts on so far. Bottom has to be pulled up inside where we can't see it.
Logged

Offline lightning

  • Pinto Member
  • **
  • Posts: 12
  • FeedBack: +0/-0
  • Gender: Male

    • Total Badges: 2
    Badges: (View All)
    Topic Starter Signature
Re: Lower ball joint help needed
« Reply #7 on: July 08, 2014, 07:29:59 PM »
Yup. Bolts just started. Top flange downside up in pic. Fixed it. Thanx for the reply.
Logged
Using Tapatalk

Offline amc49

  • PCCA VIP
  • Pinto Master
  • ***
  • Posts: 1256
  • FeedBack: +242/-1
  • Another Pinto Driver

    • Total Badges: 4
    Badges: (View All)
    Topic Starter Poll Voter Windows User 1000 Posts
Re: Lower ball joint help needed
« Reply #8 on: July 08, 2014, 08:02:24 PM »
Good deal, you caught that too.
Logged
Pages: [1]   Go Up
« previous next »