Current Classifieds

1978 FORD PINTO PONY FOR SALE 17.000 MILES !!!!!!!!!!!!

Date: 06/25/2021 12:59 am
windshield
Date: 04/14/2018 08:53 pm
 (3) 1980 Ford Pinto Station Wagon Projects

Date: 03/15/2023 02:16 pm
1978 pinto grill
Date: 07/24/2018 02:18 pm
72 Runabout for Sale- Washington

Date: 02/28/2024 02:07 pm
Mustang II V8 swap parts
Date: 03/26/2017 02:25 pm
79 pinto front,rear alum bumpers

Date: 07/17/2018 09:49 pm
turbo 4 cyl and aod trans
Date: 12/14/2019 04:55 pm
1977 pinto rear bumper
Date: 04/19/2021 11:57 am
1980 Pinto Pony for sale

Date: 08/21/2021 03:54 pm
1977 Pinto Cruizin Wagon

Date: 08/07/2023 02:52 pm
Needed- Good 71-73 Rear End or parts- close to AL
Date: 09/15/2019 12:38 pm

« previous next »
Pages: [1]   Go Down

Author Topic: Lower ball joint help needed  (Read 2312 times)

0 Members and 1 Guest are viewing this topic.

Offline lightning

  • Pinto Member
  • **
  • Posts: 12
  • FeedBack: +0/-0
  • Gender: Male

    • Total Badges: 2
    Badges: (View All)
    Topic Starter Signature
Lower ball joint help needed
« on: July 06, 2014, 05:08:17 PM »
My 78 wagon is a REAL bubba special. Bubba replaced lower BJ with uppers. Do the lowers go up through the arm or bolt on top?

Thx in advance.





Logged
Using Tapatalk

Offline enzo

  • Pinto Member
  • **
  • Posts: 74
  • FeedBack: +0/-0
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 5
    Badges: (View All)
    Mobile User Fifth year Anniversary Topic Starter Poll Voter Windows User
Re: Lower ball joint help needed
« Reply #1 on: July 06, 2014, 07:42:27 PM »
WOW. Not sure that is even possible.  Not sure if the pin taper is the same on both, as well the length and diameter!
Then there is the fact that the top b/j has 3 bolts the same size of each other, and, the lower has 4 bolts - 2 different
size of the other 2.  Has the lower control arm been modified?, cut?, and rewelded?  But, to answer your original
question, from the bottom.
Logged

Offline amc49

  • PCCA VIP
  • Pinto Master
  • ***
  • Posts: 1256
  • FeedBack: +242/-1
  • Another Pinto Driver

    • Total Badges: 4
    Badges: (View All)
    Topic Starter Poll Voter Windows User 1000 Posts
Re: Lower ball joint help needed
« Reply #2 on: July 06, 2014, 11:46:59 PM »
If bolted on top nothing holds the rubber seal down.......... .............. ..
Logged

Offline lightning

  • Pinto Member
  • **
  • Posts: 12
  • FeedBack: +0/-0
  • Gender: Male

    • Total Badges: 2
    Badges: (View All)
    Topic Starter Signature
Re: Lower ball joint help needed
« Reply #3 on: July 07, 2014, 12:58:34 AM »
The pin taper and length is diff. I had a "rattle" in the front end because it wasn't tight. 2 of the bolt holes lined up (enough for Bubba). ;(

Logged
Using Tapatalk

Offline amc49

  • PCCA VIP
  • Pinto Master
  • ***
  • Posts: 1256
  • FeedBack: +242/-1
  • Another Pinto Driver

    • Total Badges: 4
    Badges: (View All)
    Topic Starter Poll Voter Windows User 1000 Posts
Re: Lower ball joint help needed
« Reply #4 on: July 07, 2014, 07:08:45 PM »
'... replaced lower BJ with uppers.'

Whoa I totally misread that one, thought you meant all 4 got changed. My bad.

Can't get much more bubba than that.......... ..
Logged

Offline lightning

  • Pinto Member
  • **
  • Posts: 12
  • FeedBack: +0/-0
  • Gender: Male

    • Total Badges: 2
    Badges: (View All)
    Topic Starter Signature
Re: Lower ball joint help needed
« Reply #5 on: July 08, 2014, 03:01:27 PM »
Is this correct?

Logged
Using Tapatalk

Offline amc49

  • PCCA VIP
  • Pinto Master
  • ***
  • Posts: 1256
  • FeedBack: +242/-1
  • Another Pinto Driver

    • Total Badges: 4
    Badges: (View All)
    Topic Starter Poll Voter Windows User 1000 Posts
Re: Lower ball joint help needed
« Reply #6 on: July 08, 2014, 07:24:36 PM »
Could easily be, hoping the bottom flange is showing simply because you have barely threaded bolts on so far. Bottom has to be pulled up inside where we can't see it.
Logged

Offline lightning

  • Pinto Member
  • **
  • Posts: 12
  • FeedBack: +0/-0
  • Gender: Male

    • Total Badges: 2
    Badges: (View All)
    Topic Starter Signature
Re: Lower ball joint help needed
« Reply #7 on: July 08, 2014, 07:29:59 PM »
Yup. Bolts just started. Top flange downside up in pic. Fixed it. Thanx for the reply.
Logged
Using Tapatalk

Offline amc49

  • PCCA VIP
  • Pinto Master
  • ***
  • Posts: 1256
  • FeedBack: +242/-1
  • Another Pinto Driver

    • Total Badges: 4
    Badges: (View All)
    Topic Starter Poll Voter Windows User 1000 Posts
Re: Lower ball joint help needed
« Reply #8 on: July 08, 2014, 08:02:24 PM »
Good deal, you caught that too.
Logged
Pages: [1]   Go Up
« previous next »