Current Classifieds

76 station wagon parts needed.
Date: 03/14/2020 01:52 pm
13x6 minilite style wheels MAKE OFFER——NEED GONE

Date: 08/01/2018 01:17 pm
Mustang II V8 swap parts
Date: 03/26/2017 02:25 pm
'78 Pinto Windshield Trim
Date: 05/09/2017 10:46 am
1976 Ford Pinto Wagon - just rebuilt. 302 v8

Date: 11/11/2019 03:38 pm
Looking for fan shroud for 72' Pinto 1.6
Date: 04/13/2017 04:56 am
Front and rear seats for a 1976 Pinto Sedan
Date: 05/18/2020 10:22 pm
KYB shocks

Date: 02/08/2017 07:09 pm
1980 hood needed
Date: 04/23/2020 10:41 pm
77 pinto cruz. wagon
Date: 06/15/2017 09:18 pm
1972-1980 Pinto/Bobcat Wagon Drivers Side Tail Light OEM

Date: 04/20/2017 10:10 am
74 Pinto wagon armrests
Date: 01/18/2017 07:04 pm

Author Topic: Lower ball joint help needed  (Read 2263 times)

0 Members and 1 Guest are viewing this topic.

Offline lightning

  • Pinto Member
  • **
  • Posts: 12
  • FeedBack: +0/-0
  • Gender: Male

  • Total Badges: 2
    Badges: (View All)
    Topic Starter Signature
Lower ball joint help needed
« on: July 06, 2014, 05:08:17 PM »
My 78 wagon is a REAL bubba special. Bubba replaced lower BJ with uppers. Do the lowers go up through the arm or bolt on top?

Thx in advance.





Using Tapatalk

Offline enzo

  • Pinto Member
  • **
  • Posts: 74
  • FeedBack: +0/-0
  • Gender: Male
  • Another Pinto Driver

  • Total Badges: 5
    Badges: (View All)
    Mobile User Fifth year Anniversary Topic Starter Poll Voter Windows User
Re: Lower ball joint help needed
« Reply #1 on: July 06, 2014, 07:42:27 PM »
WOW. Not sure that is even possible.  Not sure if the pin taper is the same on both, as well the length and diameter!
Then there is the fact that the top b/j has 3 bolts the same size of each other, and, the lower has 4 bolts - 2 different
size of the other 2.  Has the lower control arm been modified?, cut?, and rewelded?  But, to answer your original
question, from the bottom.

Offline amc49

  • PCCA VIP
  • Pinto Master
  • ***
  • Posts: 1256
  • FeedBack: +242/-1
  • Another Pinto Driver

  • Total Badges: 4
    Badges: (View All)
    Topic Starter Poll Voter Windows User 1000 Posts
Re: Lower ball joint help needed
« Reply #2 on: July 06, 2014, 11:46:59 PM »
If bolted on top nothing holds the rubber seal down.......... .............. ..

Offline lightning

  • Pinto Member
  • **
  • Posts: 12
  • FeedBack: +0/-0
  • Gender: Male

  • Total Badges: 2
    Badges: (View All)
    Topic Starter Signature
Re: Lower ball joint help needed
« Reply #3 on: July 07, 2014, 12:58:34 AM »
The pin taper and length is diff. I had a "rattle" in the front end because it wasn't tight. 2 of the bolt holes lined up (enough for Bubba). ;(

Using Tapatalk

Offline amc49

  • PCCA VIP
  • Pinto Master
  • ***
  • Posts: 1256
  • FeedBack: +242/-1
  • Another Pinto Driver

  • Total Badges: 4
    Badges: (View All)
    Topic Starter Poll Voter Windows User 1000 Posts
Re: Lower ball joint help needed
« Reply #4 on: July 07, 2014, 07:08:45 PM »
'... replaced lower BJ with uppers.'

Whoa I totally misread that one, thought you meant all 4 got changed. My bad.

Can't get much more bubba than that.......... ..

Offline lightning

  • Pinto Member
  • **
  • Posts: 12
  • FeedBack: +0/-0
  • Gender: Male

  • Total Badges: 2
    Badges: (View All)
    Topic Starter Signature
Re: Lower ball joint help needed
« Reply #5 on: July 08, 2014, 03:01:27 PM »
Is this correct?

Using Tapatalk

Offline amc49

  • PCCA VIP
  • Pinto Master
  • ***
  • Posts: 1256
  • FeedBack: +242/-1
  • Another Pinto Driver

  • Total Badges: 4
    Badges: (View All)
    Topic Starter Poll Voter Windows User 1000 Posts
Re: Lower ball joint help needed
« Reply #6 on: July 08, 2014, 07:24:36 PM »
Could easily be, hoping the bottom flange is showing simply because you have barely threaded bolts on so far. Bottom has to be pulled up inside where we can't see it.

Offline lightning

  • Pinto Member
  • **
  • Posts: 12
  • FeedBack: +0/-0
  • Gender: Male

  • Total Badges: 2
    Badges: (View All)
    Topic Starter Signature
Re: Lower ball joint help needed
« Reply #7 on: July 08, 2014, 07:29:59 PM »
Yup. Bolts just started. Top flange downside up in pic. Fixed it. Thanx for the reply.
Using Tapatalk

Offline amc49

  • PCCA VIP
  • Pinto Master
  • ***
  • Posts: 1256
  • FeedBack: +242/-1
  • Another Pinto Driver

  • Total Badges: 4
    Badges: (View All)
    Topic Starter Poll Voter Windows User 1000 Posts
Re: Lower ball joint help needed
« Reply #8 on: July 08, 2014, 08:02:24 PM »
Good deal, you caught that too.