Current Classifieds

Bumper Guards
Date: 03/28/2017 09:27 pm
1975 Ford Pinto

Date: 01/13/2020 11:02 am
1980 Pinto taillights
Date: 12/26/2017 03:48 pm
Front Body parts needed
Date: 02/09/2018 06:09 pm
72 Pinto parts
Date: 11/14/2019 10:46 pm
rear hatch back louvers

Date: 04/18/2017 12:44 pm
2.3 carb intake

Date: 07/15/2020 09:25 pm
Trailer Hitch - 73 Pinto Wagon
Date: 02/04/2018 08:26 am
Instrument Panel with Tach wanted
Date: 05/15/2022 11:36 am
Front and rear seats for a 1976 Pinto Sedan
Date: 05/18/2020 10:22 pm
74 Driver side Wagon Fender, 74 driver side Door, Nice Wheels

Date: 09/15/2019 08:30 pm
1976 Ford Pinto

Date: 07/16/2019 02:51 am

« previous next »
Pages: [1]   Go Down

Author Topic: Lower ball joint help needed  (Read 2306 times)

0 Members and 1 Guest are viewing this topic.

Offline lightning

  • Pinto Member
  • **
  • Posts: 12
  • FeedBack: +0/-0
  • Gender: Male

    • Total Badges: 2
    Badges: (View All)
    Topic Starter Signature
Lower ball joint help needed
« on: July 06, 2014, 05:08:17 PM »
My 78 wagon is a REAL bubba special. Bubba replaced lower BJ with uppers. Do the lowers go up through the arm or bolt on top?

Thx in advance.





Logged
Using Tapatalk

Offline enzo

  • Pinto Member
  • **
  • Posts: 74
  • FeedBack: +0/-0
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 5
    Badges: (View All)
    Mobile User Fifth year Anniversary Topic Starter Poll Voter Windows User
Re: Lower ball joint help needed
« Reply #1 on: July 06, 2014, 07:42:27 PM »
WOW. Not sure that is even possible.  Not sure if the pin taper is the same on both, as well the length and diameter!
Then there is the fact that the top b/j has 3 bolts the same size of each other, and, the lower has 4 bolts - 2 different
size of the other 2.  Has the lower control arm been modified?, cut?, and rewelded?  But, to answer your original
question, from the bottom.
Logged

Offline amc49

  • PCCA VIP
  • Pinto Master
  • ***
  • Posts: 1256
  • FeedBack: +242/-1
  • Another Pinto Driver

    • Total Badges: 4
    Badges: (View All)
    Topic Starter Poll Voter Windows User 1000 Posts
Re: Lower ball joint help needed
« Reply #2 on: July 06, 2014, 11:46:59 PM »
If bolted on top nothing holds the rubber seal down.......... .............. ..
Logged

Offline lightning

  • Pinto Member
  • **
  • Posts: 12
  • FeedBack: +0/-0
  • Gender: Male

    • Total Badges: 2
    Badges: (View All)
    Topic Starter Signature
Re: Lower ball joint help needed
« Reply #3 on: July 07, 2014, 12:58:34 AM »
The pin taper and length is diff. I had a "rattle" in the front end because it wasn't tight. 2 of the bolt holes lined up (enough for Bubba). ;(

Logged
Using Tapatalk

Offline amc49

  • PCCA VIP
  • Pinto Master
  • ***
  • Posts: 1256
  • FeedBack: +242/-1
  • Another Pinto Driver

    • Total Badges: 4
    Badges: (View All)
    Topic Starter Poll Voter Windows User 1000 Posts
Re: Lower ball joint help needed
« Reply #4 on: July 07, 2014, 07:08:45 PM »
'... replaced lower BJ with uppers.'

Whoa I totally misread that one, thought you meant all 4 got changed. My bad.

Can't get much more bubba than that.......... ..
Logged

Offline lightning

  • Pinto Member
  • **
  • Posts: 12
  • FeedBack: +0/-0
  • Gender: Male

    • Total Badges: 2
    Badges: (View All)
    Topic Starter Signature
Re: Lower ball joint help needed
« Reply #5 on: July 08, 2014, 03:01:27 PM »
Is this correct?

Logged
Using Tapatalk

Offline amc49

  • PCCA VIP
  • Pinto Master
  • ***
  • Posts: 1256
  • FeedBack: +242/-1
  • Another Pinto Driver

    • Total Badges: 4
    Badges: (View All)
    Topic Starter Poll Voter Windows User 1000 Posts
Re: Lower ball joint help needed
« Reply #6 on: July 08, 2014, 07:24:36 PM »
Could easily be, hoping the bottom flange is showing simply because you have barely threaded bolts on so far. Bottom has to be pulled up inside where we can't see it.
Logged

Offline lightning

  • Pinto Member
  • **
  • Posts: 12
  • FeedBack: +0/-0
  • Gender: Male

    • Total Badges: 2
    Badges: (View All)
    Topic Starter Signature
Re: Lower ball joint help needed
« Reply #7 on: July 08, 2014, 07:29:59 PM »
Yup. Bolts just started. Top flange downside up in pic. Fixed it. Thanx for the reply.
Logged
Using Tapatalk

Offline amc49

  • PCCA VIP
  • Pinto Master
  • ***
  • Posts: 1256
  • FeedBack: +242/-1
  • Another Pinto Driver

    • Total Badges: 4
    Badges: (View All)
    Topic Starter Poll Voter Windows User 1000 Posts
Re: Lower ball joint help needed
« Reply #8 on: July 08, 2014, 08:02:24 PM »
Good deal, you caught that too.
Logged
Pages: [1]   Go Up
« previous next »