Current Classifieds

Need right door for pinto or bobcat 1977 to 1980 station wagon
Date: 08/03/2018 09:19 am
74 pinto
Date: 09/11/2016 06:32 pm
Right side strut mount for 3rd door 1979 runabout
Date: 10/04/2019 08:43 pm
78 wagon instrument y
Date: 04/30/2018 07:41 pm
72 pinto

Date: 06/23/2016 12:40 pm
73 Pinto delivery wagon drag car

Date: 02/22/2017 01:58 pm
Wanted Postal Pinto
Date: 10/26/2020 03:24 pm
looking for parts
Date: 06/19/2020 02:32 pm
Built and Injected early 2000cc Engine

Date: 04/10/2017 07:30 pm
2.3 pinto carb
Date: 08/18/2018 02:07 pm
79 pinto front,rear alum bumpers

Date: 07/17/2018 09:49 pm
Looking for fan shroud for 72' Pinto 1.6
Date: 04/13/2017 04:56 am

Author Topic: 2.0 front seal replacement.  (Read 1528 times)

0 Members and 1 Guest are viewing this topic.

Offline LongTimeFordMan

  • PCCA VIP
  • Pinto Sr. Member
  • ***
  • Posts: 450
  • FeedBack: +182/-0
  • Gender: Male
  • 1973 Red Pinto Wagon

  • Total Badges: 6
    Badges: (View All)
    Fifth year Anniversary Topic Starter Signature Windows User Linux User Mobile User
2.0 front seal replacement.
« on: February 01, 2017, 09:02:53 PM »
i have a 73 wagon, 60 k miles on factory engine.. engine runs well but the front seal leaks.. I have a front seal but cant figure out how to remove the belt gear from the crankshaft.. the gear is recessed inside the front cover with only about 3/8" clearance between the gear and the housing.. Is there a special puller made for removing the gear?.

I have a couple of spare blocks and can experiment on them. as a last resort, I was thinking to notch the housing so I could use a conventional 2 jaw puller and heating the gear to loosen it.. any suggestions
Red 1973 pinto wagon DD, SoCal desert car, Factory 4 speed, 3.40 gears, Stock engine, 14" rims and tires, 60 K original miles

Offline dick1172762

  • Vintage Pinto Racer
  • PCCA Management Board
  • Pinto Sr. Master
  • ******
  • Posts: 2623
  • FeedBack: +362/-0
  • Gender: Male
  • I'm a llama!

  • Total Badges: 7
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User 1000 Posts Tenth year Anniversary Fifth year Anniversary
Re: 2.0 front seal replacement.
« Reply #1 on: February 02, 2017, 08:45:23 AM »
There is a special tool to remove the belt gear. Its made in 2 pieces to slip over the gear. Then a round tube is slipped over the two parts. Then a bolt is used to push the tool off the crank. Got mine off of e-gay. BTW the front seal almost never leaks. The cam leaks from the pulley bolt, runs down the belt cover, leaks out the bottom, and the leak is blamed on the seal. The fix is covered on the FAQ / tech tips forum.
Its better to be a has-been, than a never was.

Offline LongTimeFordMan

  • PCCA VIP
  • Pinto Sr. Member
  • ***
  • Posts: 450
  • FeedBack: +182/-0
  • Gender: Male
  • 1973 Red Pinto Wagon

  • Total Badges: 6
    Badges: (View All)
    Fifth year Anniversary Topic Starter Signature Windows User Linux User Mobile User
Re: 2.0 front seal replacement.
« Reply #2 on: February 02, 2017, 11:34:58 AM »
Thanks.. ill check the top end near the cam...
Red 1973 pinto wagon DD, SoCal desert car, Factory 4 speed, 3.40 gears, Stock engine, 14" rims and tires, 60 K original miles

Offline 72DutchWagon

  • Pinto Full Member
  • ***
  • Posts: 182
  • FeedBack: +25/-1
  • Gender: Male
  • Another Pinto Driver

  • Total Badges: 4
    Badges: (View All)
    Fifth year Anniversary Topic Starter Poll Voter Windows User
Re: 2.0 front seal replacement.
« Reply #3 on: February 02, 2017, 02:49:54 PM »
I you do want to have a try at wrestling of the belt gear, take a look at reply 53 of my 72 DutchWagon rolling resto post (I don't know how to make a link to a certain post reply). I just used a steering wheel puller and two pieces of angle iron cut to fit, and with a tiny lip bend at the bottom, to just catch behind the gear. Soak in WD40 for a day or so. Don't put any stress on the surrounding cover, it's aluminum and will break.

Offline LongTimeFordMan

  • PCCA VIP
  • Pinto Sr. Member
  • ***
  • Posts: 450
  • FeedBack: +182/-0
  • Gender: Male
  • 1973 Red Pinto Wagon

  • Total Badges: 6
    Badges: (View All)
    Fifth year Anniversary Topic Starter Signature Windows User Linux User Mobile User
Re: 2.0 front seal replacement.
« Reply #4 on: February 02, 2017, 04:47:21 PM »
I talked to brian at racer walsh and he suggested that the leak was the camshaft seal which makes sense since there is a LOT of oil around the top and down the front of the engine and inside the bellt cover. I took off the belt and hosed off the belt area at a car wash, gonna drive some and look to see where the oil is comming from. The 2.0 has a solid cam so the leak isnt from the cam pulley bolt like on the 2.3
Red 1973 pinto wagon DD, SoCal desert car, Factory 4 speed, 3.40 gears, Stock engine, 14" rims and tires, 60 K original miles