Current Classifieds

convert to stick
Date: 05/19/2018 09:26 pm
Right side strut mount for 3rd door 1979 runabout
Date: 10/04/2019 08:43 pm
72 pinto

Date: 06/23/2016 12:40 pm
Tire needed p185/80r13
Date: 12/31/2017 09:08 pm
pinto for sale
Date: 09/11/2016 09:47 pm
Pinto Wagon
Date: 05/25/2018 01:50 pm
INTERIOR DELUX ARM RESTS - 2 PAIR

Date: 03/23/2018 09:23 pm
Pinto for sale

Date: 04/19/2017 10:15 am
'80 Pinto Wagon
Date: 02/01/2018 05:20 pm
75 wagon need parts
Date: 05/28/2020 05:19 pm
77 Cruising Wagon Front Seats
Date: 04/12/2017 12:37 pm
Mustang II C4 Transmission
Date: 07/28/2017 06:26 am

Author Topic: Interior panel plastic?  (Read 1247 times)

0 Members and 1 Guest are viewing this topic.

Offline dholvrsn

  • Pinto Master
  • *****
  • Posts: 1414
  • FeedBack: +4/-0
  • Gender: Male

  • Total Badges: 6
    Badges: (View All)
    Topic Starter Signature Tenth year Anniversary Poll Voter 1000 Posts Fifth year Anniversary
Interior panel plastic?
« on: March 10, 2017, 09:33:00 PM »
What sort of plastic are the interior panels of a Pinto made out of? I amy attempt to weld up a kick panel and  a radio bezel.
'80 MPG Pony, '80-'92
'79 porthole wagon, '06-on
'80 trunk model. '17-on
-----
'98 Dodge Ram 1500
'95 Buick Riviera
'63 Studebaker Champ
'57 Studebaker Silver Hawk
'51 Studebaker Commander Starlight
'47 Studebaker Champion
'41 Studebaker Commander Land Cruiser

Offline LongTimeFordMan

  • PCCA VIP
  • Pinto Sr. Member
  • ***
  • Posts: 450
  • FeedBack: +182/-0
  • Gender: Male
  • 1973 Red Pinto Wagon

  • Total Badges: 6
    Badges: (View All)
    Fifth year Anniversary Topic Starter Signature Windows User Linux User Mobile User
Re: Interior panel plastic?
« Reply #1 on: March 10, 2017, 11:25:56 PM »
I think the ones in my 1973 wagon kick panels are molded from  some sort of abs or polyethelyne. It does melt and can be welded with a soldering iron..  but only for cosmetic appearance.

I repaired a couple of cracks in my kick panels where they cracked at the top where the kick panel bends around the door frame.

I wasnt able fuse the crack together on both sides (front and back) but wasnt able to get enough penetration to keep the crack from reopening.

The previous owner had tried to patch them with bondo on the backside but it didnt adhere.. so you probably wont be able to glue them.

Mine were cracked at the top where they bent around the door frame.  i drilled some small .030 holes on either side of the crack and used some 18 gauge wire as a "staple" to hold the joint together.

You might also try making a backing plate from thin aluminum sheet on the back side to cover the area on both sides of the crack and pop rivet it on both sides of the crack for structural integrity then fusing the edges of the crack together with a soldering iron for cosmetics.

Or you might be able to glue on a backing panel with contact cement, then fuse the crack on the front side for cosmetics.

The rear panels in my wagon seem to be made of a different material..much less flexible and somewhat brittle. Mine tend to scratch easily, but I haven't had to repair any cracks . Just paint over the scratches.

I dont have a radio bezel but I do have the heater control bezel and I think it is either styrene or abs and I think the radio bezel would probably be the same and I would suggest trying super glue if you are able to get a seal between the sides of the crack.
Red 1973 pinto wagon DD, SoCal desert car, Factory 4 speed, 3.40 gears, Stock engine, 14" rims and tires, 60 K original miles

Offline JoeBob

  • Pinto Sr. Member
  • ****
  • Posts: 536
  • FeedBack: +51/-0
  • Gender: Male

  • Total Badges: 7
    Badges: (View All)
    Photographer Topic Starter Signature Tenth year Anniversary Poll Voter Windows User Fifth year Anniversary
Re: Interior panel plastic?
« Reply #2 on: March 11, 2017, 08:49:24 PM »
I think I have a radio bezel if someone needs it.  As far as plastic panels go I have an interesting tip; sun faded plastic of this type can be revitalized by applying a heat gun to the surface. I found this out after I painted mine.
77 yellow Bobcat hatchback
Deuteronomy 7:9

Offline DBSS1234

  • Pinto Full Member
  • ***
  • Posts: 247
  • FeedBack: +29/-0
  • Gender: Male
  • Original owner 77 CW

  • Total Badges: 6
    Badges: (View All)
    Tenth year Anniversary Mobile User Topic Starter Poll Voter Windows User Fifth year Anniversary
Re: Interior panel plastic?
« Reply #3 on: March 13, 2017, 08:19:09 AM »
Get some aluminum window screen and use a soldering iron to melt the screen into the plastic over the crack (back side obviously). This will reinforce the repair and it will not open up again.