Current Classifieds

looking for parts
Date: 06/19/2020 02:32 pm
1974 Pinto Drivers door glass and parts

Date: 02/18/2017 05:52 pm
Looking for license plate bracket, interior parts 72' Runabout
Date: 04/12/2017 08:15 am
72 Pinto parts
Date: 12/04/2018 09:56 pm
WTB 1974 or 1975 Pinto Grille and Turn Signals
Date: 04/08/2018 05:47 pm
1978 PINTO PONY FOR SALE 17,000 ORIGINAL MILES !!!!!!!
Date: 10/10/2019 09:42 pm
Bumpers
Date: 07/06/2018 04:47 pm
Pinto or Bobcat wagon wanted
Date: 08/05/2018 10:49 pm
parts needed
Date: 02/20/2017 07:58 am
WANTED: 1979 Bumper End Caps - Front and Rear
Date: 02/16/2019 10:46 am
WTB: Ford Type 9 5 speed Transmission
Date: 06/28/2019 09:14 pm
t-5 2.3 trans and new flywheel cluch and pressure plate though out bearing for sale
Date: 09/12/2018 04:07 pm

Author Topic: Intake manifold part - need identification  (Read 635 times)

0 Members and 1 Guest are viewing this topic.

Offline mdspeedster

  • Pinto Member
  • **
  • Posts: 25
  • FeedBack: +0/-0

  • Total Badges: 3
    Badges: (View All)
    Tenth year Anniversary Topic Starter Fifth year Anniversary
Intake manifold part - need identification
« on: October 13, 2020, 02:24:47 PM »
There is a part bolted to the left side of my intake manifold.
Part number on it is D42E-9E434-AB.

There are four bolts attaching it to the manifold.
There are three plugs screwed into the part. 
See attached photo. 
The engine is installed in a track roadster and I need additional room between the hood side.
What is the purpose of this part?  Can I remove it and cover the opening with a flat plate?
It has been very difficult to remove so would like to know if okay before tearing into it.   
Thanks, Bruce

Offline oldkayaker

  • Pinto Master
  • *****
  • Posts: 758
  • FeedBack: +114/-0
  • Gender: Male

  • Total Badges: 5
    Badges: (View All)
    Topic Starter Signature Windows User Tenth year Anniversary Fifth year Anniversary
Re: Intake manifold part - need identification
« Reply #1 on: October 14, 2020, 04:51:35 AM »
That block covers up the intake manifold coolant passage.  Usually one of the ports has a nipple with a hose attached for coolant flow in order to warm up the intake manifold.  Seeing as you have all the ports plugged now, replacing the block with a flat plate should provide no functional change. 

Just had to comment.  I had bad luck with a Fram oil filter.  One time when removing one, a long string of adhesive was hanging out the filter discharge.  The adhesive is suspected to have come from the internal filter construction.  If it had fully broken off, it could have block a critical oil passage.  Suggest using Wix, Mortorcraft, or anything else.
Jerry J - Jupiter, Florida

Offline mdspeedster

  • Pinto Member
  • **
  • Posts: 25
  • FeedBack: +0/-0

  • Total Badges: 3
    Badges: (View All)
    Tenth year Anniversary Topic Starter Fifth year Anniversary
Re: Intake manifold part - need identification
« Reply #2 on: October 14, 2020, 12:36:32 PM »
Jerry J,
Thanks for the feedback.
Never could understand why there was antifreeze in the intake manifold area. 
Also, thanks for your thoughts on Fram filters, never had a problem but will keep an eye on it. 
Cheers,
Bruce
   

Offline LongTimeFordMan

  • PCCA VIP
  • Pinto Sr. Member
  • ***
  • Posts: 450
  • FeedBack: +182/-0
  • Gender: Male
  • 1973 Red Pinto Wagon

  • Total Badges: 6
    Badges: (View All)
    Fifth year Anniversary Topic Starter Signature Windows User Linux User Mobile User
Re: Intake manifold part - need identification
« Reply #3 on: October 14, 2020, 10:45:44 PM »
Ive had good luck with motorcraft filters..
Red 1973 pinto wagon DD, SoCal desert car, Factory 4 speed, 3.40 gears, Stock engine, 14" rims and tires, 60 K original miles