Current Classifieds

4 speed pinto transmission

Date: 05/13/2021 05:29 pm
Front sway bar frame brackets
Date: 07/13/2017 01:05 am
Need '75 Pinto wagon front seat belt assembly housing
Date: 10/03/2018 10:46 pm
77-78 front grill
Date: 04/07/2017 12:35 am
1978 ford pinto door striker (passenger side)
Date: 09/01/2017 11:58 am
INTERIOR DELUX ARM RESTS - 2 PAIR

Date: 03/23/2018 09:23 pm
72 pinto and 88 turbo coupe

Date: 06/09/2016 04:13 am
1977 Pinto Cruizin Wagon

Date: 08/07/2023 02:52 pm
1980 Ford AM radio
Date: 12/22/2019 11:57 am
1970-1973 British 4 Speed Manual; Parts or Whole
Date: 03/17/2019 03:57 am
'72 Runabout Drivers Side Door Hinge Set
Date: 12/15/2018 02:21 am
looking for parts
Date: 06/19/2020 02:32 pm

« previous next »
Pages: [1]   Go Down

Author Topic: Intake manifold part - need identification  (Read 680 times)

0 Members and 1 Guest are viewing this topic.

Offline mdspeedster

  • Pinto Member
  • **
  • Posts: 25
  • FeedBack: +0/-0

    • Total Badges: 3
    Badges: (View All)
    Tenth year Anniversary Topic Starter Fifth year Anniversary
Intake manifold part - need identification
« on: October 13, 2020, 02:24:47 PM »
There is a part bolted to the left side of my intake manifold.
Part number on it is D42E-9E434-AB.

There are four bolts attaching it to the manifold.
There are three plugs screwed into the part. 
See attached photo. 
The engine is installed in a track roadster and I need additional room between the hood side.
What is the purpose of this part?  Can I remove it and cover the opening with a flat plate?
It has been very difficult to remove so would like to know if okay before tearing into it.   
Thanks, Bruce
Logged

Offline oldkayaker

  • Pinto Master
  • *****
  • Posts: 758
  • FeedBack: +114/-0
  • Gender: Male

    • Total Badges: 5
    Badges: (View All)
    Topic Starter Signature Windows User Tenth year Anniversary Fifth year Anniversary
Re: Intake manifold part - need identification
« Reply #1 on: October 14, 2020, 04:51:35 AM »
That block covers up the intake manifold coolant passage.  Usually one of the ports has a nipple with a hose attached for coolant flow in order to warm up the intake manifold.  Seeing as you have all the ports plugged now, replacing the block with a flat plate should provide no functional change. 

Just had to comment.  I had bad luck with a Fram oil filter.  One time when removing one, a long string of adhesive was hanging out the filter discharge.  The adhesive is suspected to have come from the internal filter construction.  If it had fully broken off, it could have block a critical oil passage.  Suggest using Wix, Mortorcraft, or anything else.
Logged
Jerry J - Jupiter, Florida

Offline mdspeedster

  • Pinto Member
  • **
  • Posts: 25
  • FeedBack: +0/-0

    • Total Badges: 3
    Badges: (View All)
    Tenth year Anniversary Topic Starter Fifth year Anniversary
Re: Intake manifold part - need identification
« Reply #2 on: October 14, 2020, 12:36:32 PM »
Jerry J,
Thanks for the feedback.
Never could understand why there was antifreeze in the intake manifold area. 
Also, thanks for your thoughts on Fram filters, never had a problem but will keep an eye on it. 
Cheers,
Bruce
   
Logged

Offline LongTimeFordMan

  • PCCA VIP
  • Pinto Sr. Member
  • ***
  • Posts: 450
  • FeedBack: +182/-0
  • Gender: Male
  • 1973 Red Pinto Wagon

    • Total Badges: 6
    Badges: (View All)
    Fifth year Anniversary Topic Starter Signature Windows User Linux User Mobile User
Re: Intake manifold part - need identification
« Reply #3 on: October 14, 2020, 10:45:44 PM »
Ive had good luck with motorcraft filters..
Logged
Red 1973 pinto wagon DD, SoCal desert car, Factory 4 speed, 3.40 gears, Stock engine, 14" rims and tires, 60 K original miles
Pages: [1]   Go Up
« previous next »