Current Classifieds

v8 springs
Date: 05/07/2017 04:46 pm
Pangra wanted
Date: 02/05/2017 01:58 pm
1975 Ford Pinto

Date: 01/13/2020 11:02 am
pinto parts for sale
Date: 07/25/2018 04:51 pm
74 hood
Date: 07/03/2017 03:46 pm
72 Pinto racecar, 2.3 ARCA engine, Quaife trans
Date: 01/10/2022 03:41 pm
2 Pinto Wagons for Sale

Date: 10/29/2018 02:02 pm
1.6 New Ford cylinder head with side draft carbs

Date: 06/12/2018 08:18 pm
LOOKING for INTERIOR PARTS, MIRRORS & A HOOD LATCH
Date: 04/06/2017 12:13 am
72 Pinto
Date: 03/07/2019 12:07 pm
Wanted Postal Pinto
Date: 09/26/2019 05:31 pm
Pinto sales literature / magazine ads/ owners manuals
Date: 03/21/2017 07:47 pm

Author Topic: Inserting 1600 cam bearings  (Read 1020 times)

0 Members and 1 Guest are viewing this topic.

Offline Wittsend

  • Pinto Master
  • *****
  • Posts: 2496
  • FeedBack: +241/-0

  • Total Badges: 8
    Badges: (View All)
    Tenth year Anniversary Mobile User Topic Starter Poll Voter 1000 Posts Linux User Windows User Fifth year Anniversary
Inserting 1600 cam bearings
« on: October 05, 2017, 10:59:45 AM »
This is a rather circuitous route..., but there is a guy from France, working on a Cortina 1600, asking on the Studebaker site for advice.  He has a proper bearing insertion tool that closely fits the bearing with shoulders. He says it goes well but eventually the bearing distorts and the cam doesn't fit. He has gone through three sets of bearings without getting them installed so as to have the cam fit.


Is there anything specific to this installation? On his behalf, thanks for any advise.

Offline 72DutchWagon

  • Pinto Full Member
  • ***
  • Posts: 182
  • FeedBack: +25/-1
  • Gender: Male
  • Another Pinto Driver

  • Total Badges: 4
    Badges: (View All)
    Fifth year Anniversary Topic Starter Poll Voter Windows User
Re: Inserting 1600 cam bearings
« Reply #1 on: October 05, 2017, 02:39:42 PM »
Wittsend, does he mention anywhere what year Cortina, and type of engine?

Offline Wittsend

  • Pinto Master
  • *****
  • Posts: 2496
  • FeedBack: +241/-0

  • Total Badges: 8
    Badges: (View All)
    Tenth year Anniversary Mobile User Topic Starter Poll Voter 1000 Posts Linux User Windows User Fifth year Anniversary
Re: Inserting 1600 cam bearings
« Reply #2 on: October 05, 2017, 04:46:53 PM »
No, they didn't say. The only thing they said was it was a Cortina with the 1600 engine and I assumed it was the Kent 1600 as they referred to putting the cam bearings in the block.

Offline 72DutchWagon

  • Pinto Full Member
  • ***
  • Posts: 182
  • FeedBack: +25/-1
  • Gender: Male
  • Another Pinto Driver

  • Total Badges: 4
    Badges: (View All)
    Fifth year Anniversary Topic Starter Poll Voter Windows User
Re: Inserting 1600 cam bearings
« Reply #3 on: October 06, 2017, 01:14:04 PM »
You could point him to this excellent thread: http://www.turbosport.co.uk/showthread.php?t=209169
A lot of people have problems with installing cam bearings in a Kent or Crossflow.
The secret seems to be that they have to be pulled, not pushed, in and out of their space, either by using a factory tool P.6031 with adaptors P.6031-3 or fabricate something like that. The adaptors seem to be crucial to keep the procedure dead straight.

In the turbosport.co. uk. forum go to: The Garage>The Technical Section>X-Flow - Pinto - BDA and Twincam, there you will find the best up to date (and vintage) tech info on Kent X-Flow and Pinto 2.0 EAO engines.
   


Offline dick1172762

  • Vintage Pinto Racer
  • PCCA Management Board
  • Pinto Sr. Master
  • ******
  • Posts: 2623
  • FeedBack: +362/-0
  • Gender: Male
  • I'm a llama!

  • Total Badges: 7
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User 1000 Posts Tenth year Anniversary Fifth year Anniversary
Re: Inserting 1600 cam bearings
« Reply #4 on: October 06, 2017, 01:59:54 PM »
Very good web site! Thanks!
Its better to be a has-been, than a never was.