Current Classifieds

turbo 4 cyl and aod trans
Date: 12/14/2019 04:55 pm
Gas Tank Sending Unit
Date: 05/22/2018 02:17 pm
Oil pan front sump style
Date: 01/10/2017 09:19 am
Ignition switch 72 pinto wagon 2.0 4 sp
Date: 12/31/2017 09:03 pm
MISC PINTO PARTS

Date: 08/27/2017 10:23 am
WTB: Factory air cleaner and fan shroud 1971 2.0
Date: 02/05/2020 11:06 am
1980 Ford AM radio
Date: 12/22/2019 11:57 am
71-73 Pinto Parts

Date: 06/06/2019 10:47 am
Wanted - 71-73 Pinto grill
Date: 12/15/2016 03:32 pm
Clutch Cable Needed
Date: 04/03/2017 10:54 pm
Pangra wanted
Date: 02/05/2017 01:58 pm
74 Wagon Interior
Date: 01/22/2017 06:38 pm

Author Topic: Inserting 1600 cam bearings  (Read 1019 times)

0 Members and 1 Guest are viewing this topic.

Offline Wittsend

  • Pinto Master
  • *****
  • Posts: 2496
  • FeedBack: +241/-0

  • Total Badges: 8
    Badges: (View All)
    Tenth year Anniversary Mobile User Topic Starter Poll Voter 1000 Posts Linux User Windows User Fifth year Anniversary
Inserting 1600 cam bearings
« on: October 05, 2017, 10:59:45 AM »
This is a rather circuitous route..., but there is a guy from France, working on a Cortina 1600, asking on the Studebaker site for advice.  He has a proper bearing insertion tool that closely fits the bearing with shoulders. He says it goes well but eventually the bearing distorts and the cam doesn't fit. He has gone through three sets of bearings without getting them installed so as to have the cam fit.


Is there anything specific to this installation? On his behalf, thanks for any advise.

Offline 72DutchWagon

  • Pinto Full Member
  • ***
  • Posts: 182
  • FeedBack: +25/-1
  • Gender: Male
  • Another Pinto Driver

  • Total Badges: 4
    Badges: (View All)
    Fifth year Anniversary Topic Starter Poll Voter Windows User
Re: Inserting 1600 cam bearings
« Reply #1 on: October 05, 2017, 02:39:42 PM »
Wittsend, does he mention anywhere what year Cortina, and type of engine?

Offline Wittsend

  • Pinto Master
  • *****
  • Posts: 2496
  • FeedBack: +241/-0

  • Total Badges: 8
    Badges: (View All)
    Tenth year Anniversary Mobile User Topic Starter Poll Voter 1000 Posts Linux User Windows User Fifth year Anniversary
Re: Inserting 1600 cam bearings
« Reply #2 on: October 05, 2017, 04:46:53 PM »
No, they didn't say. The only thing they said was it was a Cortina with the 1600 engine and I assumed it was the Kent 1600 as they referred to putting the cam bearings in the block.

Offline 72DutchWagon

  • Pinto Full Member
  • ***
  • Posts: 182
  • FeedBack: +25/-1
  • Gender: Male
  • Another Pinto Driver

  • Total Badges: 4
    Badges: (View All)
    Fifth year Anniversary Topic Starter Poll Voter Windows User
Re: Inserting 1600 cam bearings
« Reply #3 on: October 06, 2017, 01:14:04 PM »
You could point him to this excellent thread: http://www.turbosport.co.uk/showthread.php?t=209169
A lot of people have problems with installing cam bearings in a Kent or Crossflow.
The secret seems to be that they have to be pulled, not pushed, in and out of their space, either by using a factory tool P.6031 with adaptors P.6031-3 or fabricate something like that. The adaptors seem to be crucial to keep the procedure dead straight.

In the turbosport.co. uk. forum go to: The Garage>The Technical Section>X-Flow - Pinto - BDA and Twincam, there you will find the best up to date (and vintage) tech info on Kent X-Flow and Pinto 2.0 EAO engines.
   


Offline dick1172762

  • Vintage Pinto Racer
  • PCCA Management Board
  • Pinto Sr. Master
  • ******
  • Posts: 2623
  • FeedBack: +362/-0
  • Gender: Male
  • I'm a llama!

  • Total Badges: 7
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User 1000 Posts Tenth year Anniversary Fifth year Anniversary
Re: Inserting 1600 cam bearings
« Reply #4 on: October 06, 2017, 01:59:54 PM »
Very good web site! Thanks!
Its better to be a has-been, than a never was.