Current Classifieds

Sunroof shade
Date: 06/19/2019 01:33 pm
Built and Injected early 2000cc Engine

Date: 04/10/2017 07:30 pm
parting out 1975 & 80 pintos
Date: 10/31/2018 12:00 pm
Wanted 2.3 engine mount brackets and mounts
Date: 02/14/2018 01:34 am
LOTS OF 1971-1973 PARTS FOR SALE
Date: 02/03/2018 11:28 am
Front sump oil pan
Date: 01/02/2017 06:54 pm
2.0 performance parts, 2 intakes, header, ported head, more
Date: 10/25/2019 04:05 pm
Looking for front seats
Date: 08/10/2021 09:54 pm
cam pulley
Date: 05/30/2018 04:56 pm
72 PINTO WAGON

Date: 09/23/2018 06:16 pm
SVO SWAP
Date: 03/15/2018 03:12 am
NEED 77/78 MUSTANG II Left Motor Mount
Date: 04/15/2017 05:14 pm

« previous next »
Pages: [1]   Go Down

Author Topic: Idle air control signal, turbo swap, a/c  (Read 1615 times)

0 Members and 1 Guest are viewing this topic.

Offline denmach1

  • Pinto Member
  • **
  • Posts: 25
  • FeedBack: +0/-0
  • Another Pinto Driver

    • Total Badges: 2
    Badges: (View All)
    Topic Starter Windows User
Idle air control signal, turbo swap, a/c
« on: August 18, 2014, 05:36:59 PM »
I am in the middle of a turbo swap into my 77 Cruisin Wagon using a LA2 ecu. I am also installing a vintage air system. Does anyone know what type of signal I need to send to the ecu to adjust the idling when the compressor turns on? (voltage? ohms? which pin? etc...) Any help is greatly appreciated.
Logged

Offline Wittsend

  • Pinto Master
  • *****
  • Posts: 2499
  • FeedBack: +241/-0

    • Total Badges: 8
    Badges: (View All)
    Tenth year Anniversary Mobile User Topic Starter Poll Voter 1000 Posts Linux User Windows User Fifth year Anniversary
Re: Idle air control signal, turbo swap, a/c
« Reply #1 on: August 18, 2014, 06:58:49 PM »
As best I can recall an LA-2 and and LA-3 are direct swap ECU's. My Pin Out for an LA-3 shows:

 10 = A/C clutch - A/C input

54 = WAC  WOT (wide open throttle) A/C cutoff

There were also two fan control signals one of which might be relevant to the A/C:

52 = HEDF Highspeed Electro-Drive Fan

55 = EDF    Electro-Drive Fan (low speed)

Hope this helps. At the moment I don't have the "type" of signal sent only where they are going/coming from. Are you using the factory relay box?
Logged

Offline denmach1

  • Pinto Member
  • **
  • Posts: 25
  • FeedBack: +0/-0
  • Another Pinto Driver

    • Total Badges: 2
    Badges: (View All)
    Topic Starter Windows User
Re: Idle air control signal, turbo swap, a/c
« Reply #2 on: August 18, 2014, 07:11:54 PM »
Wittsend, thanks. I am using a Vintage air system and its controls. I see the a/c input on pin 10 of my diagram but just not sure what kind of signal to send to it. I can easily send 12v to it when the clutch is engaged but i need confirmation that that is what it needs. I don't want to fry anything
Logged

Offline oldkayaker

  • Pinto Master
  • *****
  • Posts: 758
  • FeedBack: +114/-0
  • Gender: Male

    • Total Badges: 5
    Badges: (View All)
    Topic Starter Signature Windows User Tenth year Anniversary Fifth year Anniversary
Re: Idle air control signal, turbo swap, a/c
« Reply #3 on: August 19, 2014, 12:44:42 PM »
The 87TC EVTM shows the LA2 pin #10 connected to the +12V side of the A/C clutch coil.  Note there is one of those surge protection diodes in the wiring harness connected across the A/C clutch coil to moderate the voltage spikes.  I believe this #10 pin is the circuit that opens the IAC a little to maintain idle speed when the A/C is on.
Logged
Jerry J - Jupiter, Florida

Offline denmach1

  • Pinto Member
  • **
  • Posts: 25
  • FeedBack: +0/-0
  • Another Pinto Driver

    • Total Badges: 2
    Badges: (View All)
    Topic Starter Windows User
Re: Idle air control signal, turbo swap, a/c
« Reply #4 on: August 19, 2014, 08:10:40 PM »
Thanks for all of the great info guys! This build would be a real struggle without this site and all of your knowledge and help.
Logged
Pages: [1]   Go Up
« previous next »