Current Classifieds

Hood Hinge rubber boots
Date: 09/28/2018 05:49 pm
1975 Ford Pinto

Date: 01/13/2020 11:02 am
Looking for Pinto manual shifter parts
Date: 01/28/2021 03:49 pm
Looking for 1.6 exhaust manifold heat shield, front license plate bracket
Date: 11/04/2018 02:34 am
2.3 front sump oil pan
Date: 07/24/2018 03:17 pm
99' 2.5l lima cylinder head

Date: 01/13/2017 01:56 am
79 pinto front,rear alum bumpers

Date: 07/17/2018 09:49 pm
'71,'72,or'73 small Ford v8 Pinto
Date: 01/23/2017 07:41 am
77 Caliper Bolt
Date: 08/21/2018 04:02 pm
1600 CC WATER PUMP
Date: 06/02/2018 09:13 am
Pinto porthole exterior trim wanted
Date: 03/30/2021 12:29 pm
Wanted Pinto Fiberglass Body Parts
Date: 05/19/2018 04:56 pm

Author Topic: Idle adjustment screw.  (Read 1427 times)

0 Members and 1 Guest are viewing this topic.

Offline John Turner

  • Pinto Member
  • **
  • Posts: 56
  • FeedBack: +0/-0
  • Another Pinto Driver

  • Total Badges: 3
    Badges: (View All)
    Topic Starter Fifth year Anniversary Apple User
Idle adjustment screw.
« on: February 14, 2013, 03:25:42 PM »
1972 Wagon, 2000cc, 2V.   I had a rebuilt carb installed and just now found out that the "idle adjustment screw" is missing.
It goes into the idle cam.  There is also a little spring that keeps it from turning once adjusted.  (missing also.)

Does anyone know what the size, thread etc. for this screw is??  Other option is to see of a carb. rebuilder would have one.  Anyone?  Bueller? Thanks guys, jt

Offline PinTodd

  • Pinto Driver
  • *
  • Posts: 4
  • FeedBack: +0/-0
  • Gender: Male

  • Total Badges: 2
    Badges: (View All)
    Topic Starter Fifth year Anniversary
Re: Idle adjustment screw.
« Reply #1 on: February 15, 2013, 09:50:41 PM »
John,
If you are talking about the screw that sits against the throttle lever to adjust idle speed, I have one with the spring that is on a busted carb that came off of my '73.  If you can send a picture of where it goes, I can see if it is in the  spot I am thinking.  If you can't send a picture and think it is the one you need, let me know.  My e-mail is Villella@fordpinto.com  I can send what I have to you at no charge.  On another note, maybe you can answer a question I have.  I just bought a 4 barrel intake that has been modified so you cannot run the heater hose through it.  Do you know of anyway I can reroute the hose coming from the heater core back into the engine without going through the intake?  Any info would help.
 
Thanks.

Offline John Turner

  • Pinto Member
  • **
  • Posts: 56
  • FeedBack: +0/-0
  • Another Pinto Driver

  • Total Badges: 3
    Badges: (View All)
    Topic Starter Fifth year Anniversary Apple User
Re: Idle adjustment screw.
« Reply #2 on: February 16, 2013, 08:34:39 AM »
Yes, that is the screw and spring that I need.  My address is John Turner, 76 Bogel Road, East Haddam, CT.  06423, include your return address in the envelope when you send it to me and I'll drop $5 in the mail to you for your trouble.  On the heater rerout, If it were me, I'd skip the intake manifold altogether, get a premeasured fresh piece of heater hose and hook it in to the sources on the heater core and then the block.  I think that the only reason it connects to the carburetor in the first place is to actuate the automatic choke via the water temperature.  (kind of a low tech approach.)  Good Luck and Thanks a ton for sending the screw and spring to me.  jt