Current Classifieds

1971 Pinto (survivor)

Date: 05/15/2022 04:42 pm
Wanted early pinto
Date: 10/03/2019 02:42 pm
Wanted: automatic transmission shifter
Date: 07/21/2017 11:49 am
77 pinto
Date: 08/22/2017 06:31 pm
Deluxe Steering Wheel
Date: 10/16/2017 08:13 am
Oil pan front sump style
Date: 01/10/2017 09:19 am
Wanted hood hinges
Date: 02/17/2020 05:30 pm
WANTED: 1979 Bumper End Caps - Front and Rear
Date: 02/16/2019 10:46 am
Built 2.0
Date: 10/07/2018 05:27 pm
1978 need kick panels and rear hatch struts and upper and lower mounts
Date: 11/29/2018 10:26 am
74 Pinto Rear Side Lights

Date: 02/18/2017 05:47 pm
convert to stick
Date: 05/19/2018 09:26 pm

Author Topic: Identification  (Read 654 times)

0 Members and 1 Guest are viewing this topic.

Offline Canadiandavid

  • Pinto Member
  • **
  • Posts: 11
  • FeedBack: +0/-0
  • Gender: Male
  • Eh

  • Total Badges: 3
    Badges: (View All)
    Signature Topic Starter Mobile User
Identification
« on: April 19, 2021, 10:24:14 PM »
Hey there, so I know my pinto has had the motor and tranny changed and I never really cared until I started looking for parts. I can say that it’s a v6 with a 5speed other than that I couldn’t tell you. When I got a thermostat gasket for a 79 v6 it looked nothing like what I needed. If anyone knows any numbers stamped somewhere without having to rip it apart that would be awesome.

Thanks a bunch
I may be dirty and smelly but  in the dark I’m just smelly

Offline Reeves1

  • Pinto Master
  • *****
  • Posts: 2158
  • FeedBack: +104/-0
  • Gender: Male
  • BAWS302

  • Total Badges: 6
    Badges: (View All)
    Tenth year Anniversary Topic Starter Signature Fifth year Anniversary Windows User 1000 Posts
Re: Identification
« Reply #1 on: April 20, 2021, 07:18:35 AM »
If it were me, I'd pull it apart & see what is there first.
No sense buying parts twice.....

Offline PintoTim2

  • Pinto Member
  • **
  • Posts: 71
  • FeedBack: +0/-0
  • Gender: Male
  • '72 Pinto & '80 Pinto Pickup

  • Total Badges: 3
    Badges: (View All)
    Fifth year Anniversary Topic Starter Mobile User
Re: Identification
« Reply #2 on: April 21, 2021, 01:42:09 PM »
What it is....   Well the Pintos had a 2.8L V6 - assuming your car is a '79 that might of been the original engine.  Assuming the engine is a cologne V6 (2.6, 2.8i, U.S. 2.8, 4.0)  The bellhousing for these engines is the same.  That's the good part...  The bad part is the "cologne V6" engine blocks have a partial bellhousing casting extend rearward so that it requires a very long transmission input shaft {or an adapter).   So if the trans is actually a 5 spd (there were none original for a cologne V6 in the US - other than the Sierra & trucks I'm pretty sure....) the question is what the trans is...  Might be a Ranger trans, a Sierra, possible a T5 (with an adapter to move the input shaft pilot bearing past the crank).  You need to pull the trans off to see how many splines on the input shaft and the clutch diameter.  The Mustang II clutches are getting hard to find the last I checked (these are 8-1/2" dia).  I have found places to rebuild them.  You need to measure the clutch disc.  If you have a T5 with a pilot bearing adapter, check this carefully - my first spun in the crank.  My cologne V6 uses a Mustang II bellhousing with 8-1/2" clutch and an early fox body V8 mustang T5.  Ratios are great.  The truck 5spds are too low in the first gear ratio & I don't think these fit without floor mods.  Good luck!