Current Classifieds

1976 (non hatchback) pinto (90% complete project)

Date: 07/10/2016 10:17 am
hubcaps

Date: 05/13/2021 05:33 pm
Floor pans for my 1975 Pinto Sedan
Date: 12/09/2016 08:34 am
Need lower control arms for 1973 pinto
Date: 02/27/2017 10:10 pm
Interior Parts
Date: 08/07/2017 03:59 pm
77 Caliper Bolt
Date: 08/21/2018 04:02 pm
Radiator
Date: 05/27/2018 06:07 am
ford pinto door panels
Date: 03/20/2022 07:51 pm
Rear Bumper
Date: 07/26/2021 01:08 pm
Needed:73 Pinto center console/change tray
Date: 12/09/2018 11:35 pm
Windshield
Date: 01/15/2022 09:31 pm
71 72 front bumper brackets
Date: 06/10/2020 10:55 am

Author Topic: I have a D-port intake question.  (Read 1680 times)

0 Members and 1 Guest are viewing this topic.

Offline richcon76

  • Pinto Member
  • **
  • Posts: 19
  • FeedBack: +0/-0
  • Gender: Male
  • The American Mini

  • Total Badges: 2
    Badges: (View All)
    Topic Starter Fifth year Anniversary
I have a D-port intake question.
« on: December 18, 2012, 10:02:34 PM »
I am running a D-port head and was woundering which intake would be better to run? One intake that I have is the early D-port (the one that a two barrel bolts to) and the other one I have is the EFI intake. I will be running a 350cfm Holley and want to know what flows better.

Offline dick1172762

  • Vintage Pinto Racer
  • PCCA Management Board
  • Pinto Sr. Master
  • ******
  • Posts: 2623
  • FeedBack: +362/-0
  • Gender: Male
  • I'm a llama!

  • Total Badges: 7
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User 1000 Posts Tenth year Anniversary Fifth year Anniversary
Re: I have a D-port intake question.
« Reply #1 on: December 19, 2012, 01:52:44 AM »
If the carb will clear your hood, the EFI is MUCH better. Much better!!!!
Its better to be a has-been, than a never was.

Offline racer99

  • Pinto Full Member
  • ***
  • Posts: 182
  • FeedBack: +4/-0
  • Gender: Male
  • Just damn junk with a bt carb

  • Total Badges: 6
    Badges: (View All)
    Fifth year Anniversary Topic Starter Poll Voter Apple User Mobile User Windows User
Re: I have a D-port intake question.
« Reply #2 on: December 19, 2012, 06:34:41 AM »
The 4 square EFI lower and an adapter works good.
I use the same intake, knife-edged with a 1 inch 4bbl spacer
tigged to it.

Offline richcon76

  • Pinto Member
  • **
  • Posts: 19
  • FeedBack: +0/-0
  • Gender: Male
  • The American Mini

  • Total Badges: 2
    Badges: (View All)
    Topic Starter Fifth year Anniversary
Re: I have a D-port intake question.
« Reply #3 on: December 19, 2012, 09:24:20 AM »
Thanks racer99 and dick1172762! I thought the efi was better, but wanted to find out. I will just put the early D-port on the shelf.

Thanks, again