Current Classifieds

Hood Hinge rubber boots
Date: 09/28/2018 05:49 pm
INTERIOR DELUX ARM RESTS - 2 PAIR

Date: 03/23/2018 09:23 pm
Seeking reveal molding for driver's door for a 1980 Squire Wagon
Date: 11/08/2020 02:10 pm
Need 2.3 timing cover
Date: 08/10/2018 11:41 am
73 Runabout

Date: 11/20/2017 03:19 pm
72 Pinto racecar, 2.3 ARCA engine, Quaife trans
Date: 01/10/2022 03:41 pm
1974 Pinto Drivers door glass and parts

Date: 02/28/2018 09:33 am
4 speed pinto transmission

Date: 05/13/2021 05:29 pm
1976-1980 A/C condensor

Date: 09/21/2020 10:43 pm
72 pinto drag car

Date: 06/22/2017 07:19 am
Looking for Passenger side Inner Fender Apron
Date: 10/28/2018 08:45 am
1975 rear end, 8 inch, drum brakes, and axles, 3.4 gear.

Date: 11/08/2019 10:01 am

Author Topic: Holly 2300 series 2 bbl carb. on a 74 pinto 2000cc  (Read 1375 times)

0 Members and 1 Guest are viewing this topic.

Offline kartracer28

  • Pinto Member
  • **
  • Posts: 14
  • FeedBack: +1/-0
  • Gender: Male
  • Another Pinto Driver

  • Total Badges: 4
    Badges: (View All)
    Topic Starter Linux User Mobile User Windows User
Holly 2300 series 2 bbl carb. on a 74 pinto 2000cc
« on: October 27, 2014, 12:15:11 PM »
 I would like to put a "better" carb on my  74 Pinto. will the Holley 2300 series 350 CFM 2BBL  be a good replacement carb. The motor is stock except for an Eslinger  header and 2  1/2" exhaust and Pertronix ignition. Will I need a  "adapter plate" for the carb?

Offline amc49

  • PCCA VIP
  • Pinto Master
  • ***
  • Posts: 1256
  • FeedBack: +242/-1
  • Another Pinto Driver

  • Total Badges: 4
    Badges: (View All)
    Topic Starter Poll Voter Windows User 1000 Posts
Re: Holly 2300 series 2 bbl carb. on a 74 pinto 2000cc
« Reply #1 on: October 27, 2014, 02:20:53 PM »
Yes and yes. The stock power valve circuit will feed too much fuel, it needs to be restricted down to like .020" holes each side.

FYI, old American Motors 2 bbl. carb adapters that used to be part of every 2 bbl. manifold make good adapters, the smaller inside hole pattern fits the small pattern on the 2.0 manifold.

Sure you got a 2.0? '74 came with 2.3........... .....

Offline kartracer28

  • Pinto Member
  • **
  • Posts: 14
  • FeedBack: +1/-0
  • Gender: Male
  • Another Pinto Driver

  • Total Badges: 4
    Badges: (View All)
    Topic Starter Linux User Mobile User Windows User
Re: Holly 2300 series 2 bbl carb. on a 74 pinto 2000cc
« Reply #2 on: October 27, 2014, 02:32:14 PM »
Yes 100% sure its a 2.0 its one of the "early" 74's I wish it was the 2.3.