Current Classifieds

KYB shocks

Date: 02/08/2017 07:09 pm
hubcaps

Date: 05/13/2021 05:33 pm
Front sway bar frame brackets
Date: 07/13/2017 01:05 am
Gazelle Replicar Pinto powered frame

Date: 01/28/2017 12:30 pm
Pinto Runabout wanted
Date: 06/05/2018 04:42 pm
Odds and Ends 1976-77 Pinto Wagon

Date: 07/17/2019 05:23 pm
1973 Pinto 2.3 4 speed transmission. Tube frame roadster frame (roller). 1971 Pinto 2.0 radiator.
Date: 09/05/2018 06:30 pm
74 Pinto wagon armrests
Date: 01/18/2017 07:04 pm
WTB 1974 or 1975 Pinto Grille and Turn Signals
Date: 04/08/2018 05:47 pm
79 pinto small parts
Date: 04/24/2019 03:16 pm
Rear Bumper
Date: 07/26/2021 01:08 pm
1973 Pinto Runabout

Date: 08/17/2022 06:27 pm

Author Topic: Holley 350 cfm restrictor kit  (Read 1442 times)

0 Members and 1 Guest are viewing this topic.

Offline MitchiePinto

  • Pinto Member
  • **
  • Posts: 76
  • FeedBack: +0/-0
  • Another Pinto Driver

  • Total Badges: 1
    Badges: (View All)
    Topic Starter
Holley 350 cfm restrictor kit
« on: October 15, 2012, 05:36:21 PM »
Currently I have a 2100 Motorcraft that is toast I rebuilt it and it runs but noticed after rebuilding it a vacuum leak coming from the throttle shaft output and there is lots of play in the shaft, latter found out that this is a common issue from wear and tear and requires a whole new carb.

I was given a 2150 off of a 318 and found it to run to rich and not idle so I removed the power valve and used a #16 power valve off the 2100 and it solved the issue but still not running right I noticed that it has external vacuum running off the power valve cover ? should I connect this to my manifold tee but theres gas running though there? is gas suppose to run under the power valve or should it be dry

Or should I just buy a Holley 350 cfm and order a restrictor kit and right sized PV and aluminum or rubber spacer

also what is the PV restrictor do? its sold from racer walsh and involves using a tap and drill bit? where exactly does it go and is it hard pricesion work? Will my car overheat with a Holley and is it fine for a standard transmission

Offline TIGGER

  • PCCA Charter Member
  • Pinto Master
  • *
  • Posts: 2422
  • FeedBack: +70/-0
  • Gender: Male

  • Total Badges: 10
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User Apple User Mobile User 1000 Posts Tenth year Anniversary Fifth year Anniversary Photographer
Re: Holley 350 cfm restrictor kit
« Reply #1 on: October 16, 2012, 02:31:56 PM »
I believe it leans out the mixture at an idle so you dont load up.  I installed one in my 500cfm.  It was pretty easy.  Just make sure you drill straight.  While i am still a little rich at an idle, it is much better than it was before.
79 4cyl Wagon
73 Turbo HB
78 Cruising Wagon (sold 8/6/11)

Offline MitchiePinto

  • Pinto Member
  • **
  • Posts: 76
  • FeedBack: +0/-0
  • Another Pinto Driver

  • Total Badges: 1
    Badges: (View All)
    Topic Starter
Re: Holley 350 cfm restrictor kit
« Reply #2 on: October 16, 2012, 03:36:33 PM »
Thanks for your comment, I think Il go with a holley 5200 re-manned from Napa just need the adapter plate