Current Classifieds

Drivers side door panel Orange
Date: 05/22/2018 01:54 pm
2.0 performance parts, 2 intakes, header, ported head, more
Date: 10/25/2019 04:05 pm
t-5 2.3 trans and new flywheel cluch and pressure plate though out bearing for sale
Date: 09/09/2018 03:22 pm
1974 Pinto Inside Rear View Mirror & Brake Pedal Pad

Date: 02/18/2017 04:41 pm
1977 Pinto Cruising Wagon FOR SALE

Date: 08/20/2017 01:34 pm
Miscellaneous Pinto parts

Date: 11/05/2017 02:29 pm
Pinto Wheel Well Trim
Date: 03/29/2017 11:35 am
2.3/C-4 torque converter needed
Date: 02/08/2018 02:26 pm
Windshield
Date: 01/15/2022 09:31 pm
Drivers side door panel Orange
Date: 05/22/2018 01:54 pm
Hatch needed
Date: 09/10/2017 09:16 pm
pinto wagon parts
Date: 12/19/2019 01:43 pm

Author Topic: Holley 350 cfm restrictor kit  (Read 1328 times)

0 Members and 1 Guest are viewing this topic.

Offline MitchiePinto

  • Pinto Member
  • **
  • Posts: 76
  • FeedBack: +0/-0
  • Another Pinto Driver

  • Total Badges: 1
    Badges: (View All)
    Topic Starter
Holley 350 cfm restrictor kit
« on: October 15, 2012, 05:36:21 PM »
Currently I have a 2100 Motorcraft that is toast I rebuilt it and it runs but noticed after rebuilding it a vacuum leak coming from the throttle shaft output and there is lots of play in the shaft, latter found out that this is a common issue from wear and tear and requires a whole new carb.

I was given a 2150 off of a 318 and found it to run to rich and not idle so I removed the power valve and used a #16 power valve off the 2100 and it solved the issue but still not running right I noticed that it has external vacuum running off the power valve cover ? should I connect this to my manifold tee but theres gas running though there? is gas suppose to run under the power valve or should it be dry

Or should I just buy a Holley 350 cfm and order a restrictor kit and right sized PV and aluminum or rubber spacer

also what is the PV restrictor do? its sold from racer walsh and involves using a tap and drill bit? where exactly does it go and is it hard pricesion work? Will my car overheat with a Holley and is it fine for a standard transmission

Offline TIGGER

  • PCCA Charter Member
  • Pinto Master
  • *
  • Posts: 2409
  • FeedBack: +70/-0
  • Gender: Male

  • Total Badges: 10
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User Apple User Mobile User 1000 Posts Tenth year Anniversary Fifth year Anniversary Photographer
Re: Holley 350 cfm restrictor kit
« Reply #1 on: October 16, 2012, 02:31:56 PM »
I believe it leans out the mixture at an idle so you dont load up.  I installed one in my 500cfm.  It was pretty easy.  Just make sure you drill straight.  While i am still a little rich at an idle, it is much better than it was before.
79 4cyl Wagon
73 Turbo HB
78 Cruising Wagon (sold 8/6/11)

Offline MitchiePinto

  • Pinto Member
  • **
  • Posts: 76
  • FeedBack: +0/-0
  • Another Pinto Driver

  • Total Badges: 1
    Badges: (View All)
    Topic Starter
Re: Holley 350 cfm restrictor kit
« Reply #2 on: October 16, 2012, 03:36:33 PM »
Thanks for your comment, I think Il go with a holley 5200 re-manned from Napa just need the adapter plate