Current Classifieds

KYB shocks

Date: 02/08/2017 07:09 pm
Looking for Radiator and gas tank
Date: 10/24/2018 07:41 am
hubcaps

Date: 06/05/2018 09:13 pm
1975 Ford Pinto

Date: 01/13/2020 11:02 am
C-3 automatic transmission

Date: 08/17/2022 10:18 am
Wanted 2.3 engine mount brackets and mounts
Date: 02/14/2018 01:34 am
Tubing bender 1/2 to 2 1/2 (3) inch roll cage / mufflers and more

Date: 03/13/2021 12:57 pm
1971 2.0 valve cover
Date: 01/25/2019 07:09 pm
Seeking parts
Date: 10/18/2020 10:35 am
FREE PARTS!!

Date: 01/10/2017 02:38 pm
Parts for 74 Squire Wagon
Date: 09/16/2019 07:35 pm
Pinto 4-spd transmissions
Date: 06/15/2018 09:15 am

« previous next »
Pages: [1]   Go Down

Author Topic: Help, replacement rack and pinion won't fit  (Read 1265 times)

0 Members and 1 Guest are viewing this topic.

Offline nothingtodo

  • Pinto Member
  • **
  • Posts: 49
  • FeedBack: +0/-0
  • Another Pinto Driver

    • Total Badges: 4
    Badges: (View All)
    Topic Starter Poll Voter Fifth year Anniversary Windows User
Help, replacement rack and pinion won't fit
« on: May 07, 2015, 07:26:34 AM »
Replacing the R&P on my 1979 due to faulty inner tie rods. I bought a replacement manual R&P from Rock Auto and looks fine, but discovered that the rag joint coupler needs a flat ground on the steering input shaft on the R&P and the replacement is perfectly round! Anyone seen this before? Not sure if I should grind a flat on shaft and use it or try to return it and find one that will work. For those of you who have replaced your manual R&P, where did you get yours from?
Logged

Offline amc49

  • PCCA VIP
  • Pinto Master
  • ***
  • Posts: 1256
  • FeedBack: +242/-1
  • Another Pinto Driver

    • Total Badges: 4
    Badges: (View All)
    Topic Starter Poll Voter Windows User 1000 Posts
Re: Help, replacement rack and pinion won't fit
« Reply #1 on: May 07, 2015, 12:11:58 PM »
I myself have no trouble with putting a flat on but it is timed to make the steering wheel straight ahead and the rack centered end to end. You don't locate it just anywhere.

Flat not being there screams possibly wrong part, I would be double checking EVERYTHING else before I butchered the part to not be able to return it. Look close at the spline all the way around, some look round but one small tooth is missing to do the same as the flat.......... .........and not obvious until you look for it.
Logged

Offline rpaulsel

  • Pinto Driver
  • *
  • Posts: 8
  • FeedBack: +0/-0
  • Gender: Male

    • Total Badges: 6
    Badges: (View All)
    Topic Starter Signature Fifth year Anniversary Mobile User Poll Voter Windows User
Re: Help, replacement rack and pinion won't fit
« Reply #2 on: May 09, 2015, 04:35:14 AM »
I replaced mine on the '76 with a part from Speedway Motors.  It worked perfectly.
Logged
76 Pinto 302 wagon
Pages: [1]   Go Up
« previous next »