Current Classifieds

76 station wagon parts needed.
Date: 03/14/2020 01:52 pm
Holley 2305 progressive 2 bbl carb 350cfm

Date: 10/11/2019 11:13 am
Hoard of Pinto parts
Date: 12/17/2016 04:14 pm
Free 2.0L Valve Cover

Date: 01/03/2023 04:27 pm
Pinto porthole exterior trim wanted
Date: 03/30/2021 12:29 pm
Offenhauser 6114 dp
Date: 09/12/2017 10:26 pm
78 hatchback

Date: 03/12/2023 06:50 pm
WTB: 2.0 Mech tach drive distributor
Date: 04/14/2023 06:15 am
Gazelle Replicar Pinto powered frame

Date: 01/28/2017 12:30 pm
78 wagon instrument y
Date: 04/30/2018 07:41 pm
1971-1975 Pinto
Date: 01/09/2017 04:14 pm
WTB: Ford Type 9 5spd Transmission
Date: 03/18/2020 01:30 am

« previous next »
Pages: [1]   Go Down

Author Topic: Help, replacement rack and pinion won't fit  (Read 1264 times)

0 Members and 1 Guest are viewing this topic.

Offline nothingtodo

  • Pinto Member
  • **
  • Posts: 49
  • FeedBack: +0/-0
  • Another Pinto Driver

    • Total Badges: 4
    Badges: (View All)
    Topic Starter Poll Voter Fifth year Anniversary Windows User
Help, replacement rack and pinion won't fit
« on: May 07, 2015, 07:26:34 AM »
Replacing the R&P on my 1979 due to faulty inner tie rods. I bought a replacement manual R&P from Rock Auto and looks fine, but discovered that the rag joint coupler needs a flat ground on the steering input shaft on the R&P and the replacement is perfectly round! Anyone seen this before? Not sure if I should grind a flat on shaft and use it or try to return it and find one that will work. For those of you who have replaced your manual R&P, where did you get yours from?
Logged

Offline amc49

  • PCCA VIP
  • Pinto Master
  • ***
  • Posts: 1256
  • FeedBack: +242/-1
  • Another Pinto Driver

    • Total Badges: 4
    Badges: (View All)
    Topic Starter Poll Voter Windows User 1000 Posts
Re: Help, replacement rack and pinion won't fit
« Reply #1 on: May 07, 2015, 12:11:58 PM »
I myself have no trouble with putting a flat on but it is timed to make the steering wheel straight ahead and the rack centered end to end. You don't locate it just anywhere.

Flat not being there screams possibly wrong part, I would be double checking EVERYTHING else before I butchered the part to not be able to return it. Look close at the spline all the way around, some look round but one small tooth is missing to do the same as the flat.......... .........and not obvious until you look for it.
Logged

Offline rpaulsel

  • Pinto Driver
  • *
  • Posts: 8
  • FeedBack: +0/-0
  • Gender: Male

    • Total Badges: 6
    Badges: (View All)
    Topic Starter Signature Fifth year Anniversary Mobile User Poll Voter Windows User
Re: Help, replacement rack and pinion won't fit
« Reply #2 on: May 09, 2015, 04:35:14 AM »
I replaced mine on the '76 with a part from Speedway Motors.  It worked perfectly.
Logged
76 Pinto 302 wagon
Pages: [1]   Go Up
« previous next »