Current Classifieds

WTB - 1979 Fan Shroud - D52E-8246-CIB
Date: 11/05/2020 06:32 pm
Pinto Wheel Well Trim
Date: 03/29/2017 11:35 am
LOTS OF 1971-1973 PARTS FOR SALE
Date: 02/03/2018 11:28 am
74 Wagon body parts and a couple of 79 bits

Date: 11/14/2019 04:02 am
1976-1979 FORD PINTO BOBCAT FRONT HOOD TRIM MOLDING D4FZ-16856-A OEM EXCELLENT

Date: 09/22/2020 11:33 pm
79 pinto headlight,tailight,side marker light assemblies

Date: 07/17/2018 09:22 pm
Clutch Pedals for 75to 80 Pinto
Date: 09/21/2018 11:35 am
2.3 pinto carb
Date: 08/18/2018 02:07 pm
Pinto Vinyl Top

Date: 10/09/2020 10:29 pm
Need Interior Panels
Date: 07/09/2018 04:59 pm
Needed, 2.0 or 2.3 motors
Date: 09/30/2018 07:47 pm
1978 pinto brake booster needed.
Date: 04/07/2021 06:12 pm

Author Topic: heater issues  (Read 2213 times)

0 Members and 1 Guest are viewing this topic.

Offline pinto bismol

  • Pinto Member
  • **
  • Posts: 30
  • FeedBack: +0/-0
  • Gender: Male
  • PINTO POWER!!!

  • Total Badges: 3
    Badges: (View All)
    Topic Starter Signature Windows User
heater issues
« on: October 27, 2014, 05:53:13 PM »
well, for the first time since I got her it is cold enough to turn on the heat.
It's blowing cool air. grrrr! changed out the heater control valve and checked the coolant level.
Thermostat next? Heater core maybe? what's my next check before I just buy all new stuff?
Caution.....ex plosive personality!

Offline 76hotrodpinto

  • Pinto Sr. Member
  • ****
  • Posts: 692
  • FeedBack: +13/-0
  • Gender: Male

  • Total Badges: 3
    Badges: (View All)
    Topic Starter Signature Windows User
Re: heater issues
« Reply #1 on: October 27, 2014, 10:41:06 PM »
If you drain some coolant you can disconnect both heater hoses, water pump and manifold. Then try to blow thru it, do not use a compressor, just man up and blow it. If it's passing air it should be ok. There are also two gaskets that are on either end of the intake manifold, I've seen people use gaskets that block the coolant at one or both of these passages. I don't know why, just undone a few. Hope that helps.
1976 half hatch 2.3 turbo w/t5.

Offline sedandelivery

  • Pinto Sr. Member
  • ****
  • Posts: 460
  • FeedBack: +30/-0
  • Gender: Male
  • Another Pinto Driver

  • Total Badges: 5
    Badges: (View All)
    Tenth year Anniversary Topic Starter Poll Voter Fifth year Anniversary Windows User
Re: heater issues
« Reply #2 on: October 28, 2014, 06:56:01 AM »
When your engine is nice and warm, feel your heater hoses to see if both are warm, If not, the core could be blocked. If the radiator doesn't really get warm, it could be the thermostat.  If all that is good, see if the cables going to the blend door are hooked up correctly, there are plastic clips on there that do break.

Offline Jerry merrill

  • Pinto Member
  • **
  • Posts: 60
  • FeedBack: +1/-0
  • Gender: Male
  • Another Pinto Driver

  • Total Badges: 4
    Badges: (View All)
    Fifth year Anniversary Topic Starter Poll Voter Windows User
Re: heater issues
« Reply #3 on: October 28, 2014, 11:02:20 PM »
I just got my heater working, in my case I had one heater hose hooked up to the water pump and one to the fitting on the thermostat housing which only flows when the thermostat is open which during the winter is almost never with the 190 deg. thermostat in it. Finally put a fitting on the intake manifold and switched the one from thermostat housing, now works great.

Offline oldkayaker

  • Pinto Master
  • *****
  • Posts: 758
  • FeedBack: +114/-0
  • Gender: Male

  • Total Badges: 5
    Badges: (View All)
    Topic Starter Signature Windows User Tenth year Anniversary Fifth year Anniversary
Re: heater issues
« Reply #4 on: October 29, 2014, 03:00:25 AM »
The heater hose connection opening in the thermostat housing is on the engine side of the thermostat diaphragm so the heater hose connection should be flowing at all times when the engine is running .  If it is not flowing, maybe it is corroded shut, or thermostat is installed backwards, or?  From what I can determine, the intake/carb connection is to keep them from freezing up and keep the fuel atomized.  If it is cold where you are at already, this would be a good thing.
Jerry J - Jupiter, Florida

Offline amc49

  • PCCA VIP
  • Pinto Master
  • ***
  • Posts: 1256
  • FeedBack: +242/-1
  • Another Pinto Driver

  • Total Badges: 4
    Badges: (View All)
    Topic Starter Poll Voter Windows User 1000 Posts
Re: heater issues
« Reply #5 on: October 29, 2014, 10:01:59 AM »
If stat not closing all the way to make good heat  it will reflect at the temp gauge if working right, the needle will be somewhat lower than normal.

Make sure if a/c is equipped with a bypass door that the door is closing or no heat at all since the air does not go through heater core, rather, it shortcuts at the bypass door. My Focus does not heat at all because a stupid plastic shaft stripped on the airbox and no heat. I have to climb under dash and flip a door by hand to make instant heat. Done in seconds but not pretty when you weight 250 lbs. You have to yank the dash to fix that shaft, not ready to go there yet (if ever).