Current Classifieds

looking for 1978 pinto head rebuild kit
Date: 05/24/2020 08:19 am
New cam

Date: 01/23/2017 05:11 pm
71-73 2.0 4 speed transmission wanted
Date: 09/06/2020 01:57 am
2.3 engine and other parts- Free
Date: 12/13/2016 10:25 am
1976 Ford Pinto

Date: 07/16/2019 02:51 am
1971 Pinto Runabout turn key driver

Date: 07/01/2019 12:23 pm
1977 Pinto for parts

Date: 10/10/2018 06:25 pm
1970-1973 British 4 Speed Manual; Parts or Whole
Date: 03/17/2019 03:57 am
Need hatchback fuel tank sending unit
Date: 08/13/2018 02:46 pm
Drivers side door panel Orange
Date: 05/22/2018 01:54 pm
1980 Pinto taillights
Date: 12/26/2017 03:48 pm
door sills
Date: 03/14/2020 03:20 pm

Author Topic: Heater control cables for a ‘71?  (Read 1082 times)

0 Members and 1 Guest are viewing this topic.

Offline fozzy

  • Pinto Member
  • **
  • Posts: 61
  • FeedBack: +1/-0
  • Gender: Male
  • mechanic

  • Total Badges: 6
    Badges: (View All)
    Topic Starter Fifth year Anniversary Poll Voter Apple User Mobile User Windows User
Heater control cables for a ‘71?
« on: June 26, 2019, 03:23:27 AM »
What do you all use for heater control cables?

I’ve got a couple old ones but the plastic ends are broken, they might work with heat shrink tubing to re-enforce them.
I was debating using manual choke cables cut to length. My dash is custom also so factory cables may not work anyway.

Does anyone have pics of how the cables are attached to the switch/control panel?

Offline LongTimeFordMan

  • PCCA VIP
  • Pinto Sr. Member
  • ***
  • Posts: 450
  • FeedBack: +182/-0
  • Gender: Male
  • 1973 Red Pinto Wagon

  • Total Badges: 6
    Badges: (View All)
    Fifth year Anniversary Topic Starter Signature Windows User Linux User Mobile User
Re: Heater control cables for a ‘71?
« Reply #1 on: June 26, 2019, 11:24:40 AM »
Hi..

The plastic ends of my heate control cables were broken as well and i repaired them.by wrapping about 1/2 " of .030 steel utility wire around the cable housing, leaving a couple of inches wire free to secure the cable to the anchor points on the control.and heater. Then i glued the wire wrapping to the cable housing to secure it. Just be careful to lube the wire inside rhe xable and avoid gett8ng glue into the cable. If you wind the wire wrap tight enough around the housing and maybe wrap for an inch or so you may not need to glue it.

Then just wrap the cree ends of wire wrap around the anchor points on the controls to secure the cable.

I am adding a water bypass valve to my heater system under the hood and will be using a standard choke cable connected to the heat lever to actuate it.
Red 1973 pinto wagon DD, SoCal desert car, Factory 4 speed, 3.40 gears, Stock engine, 14" rims and tires, 60 K original miles

Offline 71v8Pinto

  • Pinto Member
  • **
  • Posts: 29
  • FeedBack: +14/-0
  • Gender: Male
  • Another Pinto Driver

  • Total Badges: 3
    Badges: (View All)
    Poll Voter Mobile User Topic Starter
Re: Heater control cables for a ‘71?
« Reply #2 on: July 10, 2019, 03:27:59 AM »
There was a NOS one on eBay a while ago, it still might be there.
71v8Pinto

Offline robertwwithee

  • Pinto Full Member
  • ***
  • Posts: 228
  • FeedBack: +4/-0
  • Another Pinto Driver

  • Total Badges: 2
    Badges: (View All)
    Mobile User Topic Starter
Re: Heater control cables for a ‘71?
« Reply #3 on: July 10, 2019, 02:01:36 PM »
I remade mine with 2 universal choke cables.  Made a steel bracket and welded it unto cables.

Sent from my SM-G930P using Tapatalk


Offline Scott Hamilton

  • FordPinto.com Founder
  • Administrator
  • Pinto Sr. Master
  • ******
  • Posts: 2985
  • FeedBack: +131/-0
  • Gender: Male
  • Serving the Pinto Community since 1999...
    • FordPinto.com

  • Total Badges: 13
    Badges: (View All)
    Webmaster Topic Starter Signature Poll Voter PCCA Meet- 2007 Tennessee Apple User Mobile User Linux User Windows User 1000 Posts Tenth year Anniversary Fifth year Anniversary Photographer
Re: Heater control cables for a ‘71?
« Reply #4 on: July 23, 2019, 12:04:49 PM »
Yellow 72, Runabout, 2000cc, 4Spd
Green 72, Runabout, 2000cc, 4Spd

Offline mklarose

  • Pinto Member
  • **
  • Posts: 22
  • FeedBack: +0/-0
  • Gender: Male
  • Nova Scotia Pinto

  • Total Badges: 1
    Badges: (View All)
    Topic Starter
Re: Heater control cables for a ‘71?
« Reply #5 on: February 27, 2020, 08:37:19 AM »
I just repaired my cable and this process worked for me. As stated earlier the ends are just wire wound around the post. Mine broke at the heater box end, the smaller diameter plastic sleeve broke off. I did glue and heat shrink the end which made for strong end but instead of securing using the repaired smaller diameter plastic end I used a "P" clamp/cushion clamp commonly used in aircraft wiring.  I set aside the original retaining clip and secured the cable with the "P" clamp on the larger diameter plastic end and the original screw hole. Its very secure, no car modifications required and slides like new.