Current Classifieds

1980 Pinto Parts

Date: 08/05/2020 04:20 pm
Bellhousing for C4 to 2.0 litre pinto
Date: 01/30/2017 01:48 pm
1977 Left Side quarter panel
Date: 06/10/2019 04:16 pm
Front and rear seats for a 1976 Pinto Sedan
Date: 05/18/2020 10:22 pm
1979 pinto
Date: 04/19/2018 02:02 am
Wanted: automatic transmission shifter
Date: 07/21/2017 11:49 am
 1971 ford pinto items for sale

Date: 08/03/2017 07:40 pm
'71,'72,or'73 small Ford v8 Pinto
Date: 01/23/2017 07:41 am
13" Style Steel Trim Rings

Date: 10/09/2020 10:35 pm
postal pinto
Date: 06/03/2020 09:31 am
1976 pinto for sale

Date: 01/12/2017 02:08 pm
WTB Cruising Wagon
Date: 12/07/2016 05:35 pm

« previous next »
Pages: [1]   Go Down

Author Topic: Installing door weatherstripping  (Read 708 times)

0 Members and 1 Guest are viewing this topic.

Offline 442

  • Pinto Member
  • **
  • Posts: 38
  • FeedBack: +1/-0
  • Gender: Male
  • 72' Pinto hatchback project

    • Total Badges: 2
    Badges: (View All)
    Topic Starter Mobile User
Installing door weatherstripping
« on: August 21, 2019, 06:13:46 AM »
I bought aftermarket door seals for my 72 hatch and am looking for advice on installing them.  It looks like the original seals were held in place by a bunch of little T shaped retainers, but not sure how they held anything unless they were imbedded in the original seals?  (Seals are missing on the car).  Do you guys just glue the seals and call it a day?

Thanks
Logged

Offline JoeBob

  • Pinto Sr. Member
  • ****
  • Posts: 536
  • FeedBack: +51/-0
  • Gender: Male

    • Total Badges: 7
    Badges: (View All)
    Photographer Topic Starter Signature Tenth year Anniversary Poll Voter Windows User Fifth year Anniversary
Re: Installing door weatherstripping
« Reply #1 on: August 21, 2019, 12:39:02 PM »

I redid my door seals just 6 months ago. I received "T" clips with the replacement seals. My new rubber did not come with premanufacture d holes for clip insert.  A member here suggested I use a soldering gun to melt holes where needed. I worked well.
   Install rubber and hold in place with tape. Bend back the rubber to make new hole adjacent to intended receipt hole in door frame.
When I removed the old seals there was some glue at the sharp turn but was dry every where else.
My seals seem to fit well yet leak a little air. I am going to remove it and add glue all around. I also found that the new clips did not hold as well as the original clips so I reused them.
    I believe you may not have clips. I would try Rockauto of Original Parts Group. No one has pinto parts but most fords of that vintage are the same.
Good luck
Bill
   
Logged
77 yellow Bobcat hatchback
Deuteronomy 7:9

Offline 442

  • Pinto Member
  • **
  • Posts: 38
  • FeedBack: +1/-0
  • Gender: Male
  • 72' Pinto hatchback project

    • Total Badges: 2
    Badges: (View All)
    Topic Starter Mobile User
Re: Installing door weatherstripping
« Reply #2 on: August 21, 2019, 12:51:48 PM »
Thanks for the insight Bill, I will try that method with the soldering gun and use glue as well.  I do still have the original retainers, may as well use them.

Richard
Logged

Offline 442

  • Pinto Member
  • **
  • Posts: 38
  • FeedBack: +1/-0
  • Gender: Male
  • 72' Pinto hatchback project

    • Total Badges: 2
    Badges: (View All)
    Topic Starter Mobile User
Re: Installing door weatherstripping
« Reply #3 on: August 23, 2019, 12:48:51 PM »
I installed the door seals this morning using the method you advised and it worked great, thanks again for the help!
Logged
Pages: [1]   Go Up
« previous next »