Current Classifieds

Cruiser Dash Gauges
Date: 12/04/2016 11:50 am
Wanted Pinto Fiberglass Body Parts
Date: 08/16/2018 08:54 am
1.6 New Ford cylinder head with side draft carbs

Date: 06/12/2018 08:18 pm
WTB: Ford Type 9 5 speed Transmission
Date: 06/28/2019 09:14 pm
pinto wagon parts
Date: 12/19/2019 01:43 pm
free transmissions
Date: 11/28/2019 10:21 am
Wagon hatch letters
Date: 12/31/2023 04:24 pm
Looking for leaf spring insulators
Date: 04/04/2020 09:38 am
Looking for front seats
Date: 08/10/2021 09:54 pm
SOME PARTS FOR SALE
Date: 01/11/2017 10:45 am
1978 hatch back

Date: 11/29/2019 03:18 pm
Want seals for Pinto wagon "flip out" windows
Date: 08/08/2017 01:44 pm

« previous next »
Pages: [1]   Go Down

Author Topic: Installing door weatherstripping  (Read 690 times)

0 Members and 1 Guest are viewing this topic.

Offline 442

  • Pinto Member
  • **
  • Posts: 38
  • FeedBack: +1/-0
  • Gender: Male
  • 72' Pinto hatchback project

    • Total Badges: 2
    Badges: (View All)
    Topic Starter Mobile User
Installing door weatherstripping
« on: August 21, 2019, 06:13:46 AM »
I bought aftermarket door seals for my 72 hatch and am looking for advice on installing them.  It looks like the original seals were held in place by a bunch of little T shaped retainers, but not sure how they held anything unless they were imbedded in the original seals?  (Seals are missing on the car).  Do you guys just glue the seals and call it a day?

Thanks
Logged

Offline JoeBob

  • Pinto Sr. Member
  • ****
  • Posts: 536
  • FeedBack: +51/-0
  • Gender: Male

    • Total Badges: 7
    Badges: (View All)
    Photographer Topic Starter Signature Tenth year Anniversary Poll Voter Windows User Fifth year Anniversary
Re: Installing door weatherstripping
« Reply #1 on: August 21, 2019, 12:39:02 PM »

I redid my door seals just 6 months ago. I received "T" clips with the replacement seals. My new rubber did not come with premanufacture d holes for clip insert.  A member here suggested I use a soldering gun to melt holes where needed. I worked well.
   Install rubber and hold in place with tape. Bend back the rubber to make new hole adjacent to intended receipt hole in door frame.
When I removed the old seals there was some glue at the sharp turn but was dry every where else.
My seals seem to fit well yet leak a little air. I am going to remove it and add glue all around. I also found that the new clips did not hold as well as the original clips so I reused them.
    I believe you may not have clips. I would try Rockauto of Original Parts Group. No one has pinto parts but most fords of that vintage are the same.
Good luck
Bill
   
Logged
77 yellow Bobcat hatchback
Deuteronomy 7:9

Offline 442

  • Pinto Member
  • **
  • Posts: 38
  • FeedBack: +1/-0
  • Gender: Male
  • 72' Pinto hatchback project

    • Total Badges: 2
    Badges: (View All)
    Topic Starter Mobile User
Re: Installing door weatherstripping
« Reply #2 on: August 21, 2019, 12:51:48 PM »
Thanks for the insight Bill, I will try that method with the soldering gun and use glue as well.  I do still have the original retainers, may as well use them.

Richard
Logged

Offline 442

  • Pinto Member
  • **
  • Posts: 38
  • FeedBack: +1/-0
  • Gender: Male
  • 72' Pinto hatchback project

    • Total Badges: 2
    Badges: (View All)
    Topic Starter Mobile User
Re: Installing door weatherstripping
« Reply #3 on: August 23, 2019, 12:48:51 PM »
I installed the door seals this morning using the method you advised and it worked great, thanks again for the help!
Logged
Pages: [1]   Go Up
« previous next »