Current Classifieds

72 pinto drag car

Date: 07/08/2017 08:25 pm
1974 Pinto Misc. moldings & parts

Date: 12/20/2016 10:47 pm
1974 points distributor for 2.3l
Date: 07/04/2022 07:55 pm
Parting out 77 Bobcat Hatch
Date: 11/06/2017 04:16 pm
Wanted Type 9 5spd Transmission
Date: 07/04/2017 03:26 pm
Looking for Pinto manual shifter parts
Date: 01/28/2021 03:49 pm
Pinto porthole exterior trim wanted
Date: 03/30/2021 12:29 pm
Ignition switch 72 pinto wagon 2.0 4 sp
Date: 12/31/2017 09:03 pm
'72 Runabout Drivers Side Door Hinge Set
Date: 12/15/2018 02:21 am
Offenhauser 6114 dp
Date: 09/12/2017 10:26 pm
'72 Runabout Drivers Side Door Hinge Set
Date: 12/15/2018 02:21 am
Weber dcoe intake 2.0

Date: 08/01/2018 01:09 pm

« previous next »
Pages: [1]   Go Down

Author Topic: Has anyone here used a small block C6 trans, and what did you do to make it fit?  (Read 789 times)

0 Members and 1 Guest are viewing this topic.

Offline russosborne

  • Pinto Master
  • *****
  • Posts: 2405
  • FeedBack: +47/-1
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 5
    Badges: (View All)
    Poll Voter Mobile User Topic Starter Signature 1000 Posts
Has anyone here used a small block C6 trans, and what did you do to make it fit?
« on: October 31, 2018, 11:49:09 PM »
I've been doing lots of searching here and the internet in general, but other than hearing the "it won't work without lots of work" type comments I haven't found anything that has been done to make one fit.

351W engine.

If I have to drastically modify the tunnel or firewall so be it, but I am hoping to get some direction before I start. The car is already drastically modified so a little more won't hurt anything but my wallet.  ::)

Thanks,
Russ
Logged
In Glendale, Arizona

RIP Casey, Mallory, Abby, and Sadie. We miss you.

79 Pinto ESS fully caged fun car. In progress. 8inch 4.10 gears. 351C and a T5 waiting to go in.

Offline russosborne

  • Pinto Master
  • *****
  • Posts: 2405
  • FeedBack: +47/-1
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 5
    Badges: (View All)
    Poll Voter Mobile User Topic Starter Signature 1000 Posts
Re: Has anyone here used a small block C6 trans, and what did you do to make it fit?
« Reply #1 on: November 03, 2018, 10:12:05 PM »
Update.
I am going to go manual, it's what I really want. So what if it takes me another month or two.
Thanks,
Russ
Logged
In Glendale, Arizona

RIP Casey, Mallory, Abby, and Sadie. We miss you.

79 Pinto ESS fully caged fun car. In progress. 8inch 4.10 gears. 351C and a T5 waiting to go in.

Offline pinto_one

  • Pinto Master
  • *****
  • Posts: 1008
  • FeedBack: +70/-0
  • Gender: Male
  • Pinto-One

    • Total Badges: 10
    Badges: (View All)
    1000 Posts Photographer Tenth year Anniversary Topic Starter Signature Poll Voter Mobile User Apple User Windows User Fifth year Anniversary
Re: Has anyone here used a small block C6 trans, and what did you do to make it fit?
« Reply #2 on: November 04, 2018, 08:06:22 PM »
A good built C4 will work , even if the 351 pulls over500 HP it will live , and much cheaper in the long run , one you can use the stock shifter if you like , it fits the tunnel , it’s also the same gear ratio as the heavy c6 , standard is nice also , T5 are kind of
cheep but almost the same money , well at least where I live ,
Logged
76 Pinto sedan V6 , 79 pinto cruiser wagon V6 soon to be diesel or 4.0

Offline russosborne

  • Pinto Master
  • *****
  • Posts: 2405
  • FeedBack: +47/-1
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 5
    Badges: (View All)
    Poll Voter Mobile User Topic Starter Signature 1000 Posts
Re: Has anyone here used a small block C6 trans, and what did you do to make it fit?
« Reply #3 on: November 04, 2018, 10:31:24 PM »
Thanks.
I was using the C6 as that is what I have, came with the engine.
But I am going for broke (literally) and putting a manual in.
Already have a steel MII sized bellhousing on order.
Russ
Logged
In Glendale, Arizona

RIP Casey, Mallory, Abby, and Sadie. We miss you.

79 Pinto ESS fully caged fun car. In progress. 8inch 4.10 gears. 351C and a T5 waiting to go in.
Pages: [1]   Go Up
« previous next »