Current Classifieds

Needed- Good 71-73 Rear End or parts- close to AL
Date: 09/15/2019 12:38 pm
Dumping '80 yellow Pinto

Date: 06/21/2017 03:45 pm
oldskool787
Date: 02/12/2017 12:42 pm
Pinto for sale

Date: 04/19/2017 10:15 am
72 Pinto parts
Date: 11/14/2019 10:46 pm
1972 Pinto SCCA BS race car

Date: 10/23/2018 04:01 pm
need 1978 pinto guage cluster
Date: 03/07/2021 07:35 am
Pangra wanted
Date: 02/05/2017 01:58 pm
1976 Ford Pinto

Date: 07/16/2019 02:51 am
1971 Pinto Runabout turn key driver

Date: 07/01/2019 12:23 pm
78-80 Windshield
Date: 10/29/2021 03:11 pm
1974 Pinto Passenger side door glass and door parts

Date: 02/28/2018 09:18 am

Author Topic: gas smell carb help plase  (Read 740 times)

0 Members and 1 Guest are viewing this topic.

Offline ToniJ1960

  • Pinto Sr. Member
  • ****
  • Posts: 544
  • FeedBack: +13/-0
  • Gender: Female
  • Another Pinto Driver

  • Total Badges: 5
    Badges: (View All)
    Tenth year Anniversary Topic Starter Poll Voter Fifth year Anniversary Windows User
gas smell carb help plase
« on: August 10, 2018, 02:51:38 PM »
 Well the stupid vette is broke down again so good old Pinto is in charge again. Got some new 13s again on it and its running great ven when the idle drops way too low it still keeps going :)

 But the gas smell :( I looked under the hood the hoses look ok and its only when Im driving with some rpms I seem to smell it.

I took the air cleaner off to look at the carb and there was some wet gas on top of both throttle plates, and in the little well area in front of the throttle bores, semi rectangular. Theres some liquid gas visible down in there but none on top anywhere. I think thats the vent area for the bowl?

 I doubt its loading up because the idle stays perfect for 10 minutes or more no sign of rpms dropping like it would if it was loading up. The carb isnt difficult to do Im just wondering what I missed last time I had it apart.

 Any ideas? This car served me and my family well for 30 yaers is the most reliable  car ever only failed to start 2 times in over 32 yeas I had it.

Offline Wittsend

  • Pinto Master
  • *****
  • Posts: 2496
  • FeedBack: +241/-0

  • Total Badges: 8
    Badges: (View All)
    Tenth year Anniversary Mobile User Topic Starter Poll Voter 1000 Posts Linux User Windows User Fifth year Anniversary
Re: gas smell carb help plase
« Reply #1 on: August 10, 2018, 11:40:09 PM »
 It sounds like the Pinto has sat for a while?  The gas on the throttle plate is likely coming from the fuel bowl vent. This cn be from a number of places:

1. The neddle and seat have dirt in them.

2. The needle has a rubber tip that has rotted and gas is leaking into the bowl.

3. The float has gone bad and has a leak (internally).

I'd start by checking the needle and seat for debris. If the tip is rubber and it looks shot replace it (I'd rebuild the whole carb). When you get that far in it will be obvious if the float has a leak as you will feel fuel in it when shaken.

Offline ToniJ1960

  • Pinto Sr. Member
  • ****
  • Posts: 544
  • FeedBack: +13/-0
  • Gender: Female
  • Another Pinto Driver

  • Total Badges: 5
    Badges: (View All)
    Tenth year Anniversary Topic Starter Poll Voter Fifth year Anniversary Windows User
Re: gas smell carb help plase
« Reply #2 on: August 11, 2018, 03:05:45 PM »
 It could be the float isnt adjusted right?

Offline Wittsend

  • Pinto Master
  • *****
  • Posts: 2496
  • FeedBack: +241/-0

  • Total Badges: 8
    Badges: (View All)
    Tenth year Anniversary Mobile User Topic Starter Poll Voter 1000 Posts Linux User Windows User Fifth year Anniversary
Re: gas smell carb help plase
« Reply #3 on: August 11, 2018, 05:31:33 PM »
Possibly, but I doubt it. Most floats setting are fixed and unless something comes loose (on those that can be adjusted externally) that generally doesn't change. If some was in there tweaking things..., then yes it could be an issue.  A bad rubber tip on a float needle can also cause the float to rise. But, that is a secondasry effect of a primary (needle tip) problem.